Subash Khanal
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Subash Khanal has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Goutam Chattopadhyay
NASA Jet Propulsion Laboratory, California Institute of Technology, Pasadena, CA, USA
4 shared publications - Cecile Jung-Kubiak
Jet Propulsion Laboratory, California Institute of Technology, Pasadena, CA, USA
3 shared publications - Sofia Rahiminejad
Jet Propulsion Laboratory, California Institute of Technology, Pasadena, CA, USA
3 shared publications - Sven van Berkel
Jet Propulsion Laboratory, California Institute of Technology, Pasadena, CA, USA
3 shared publications - Alain Eric Maestrini
Jet Propulsion Laboratory, California Institute of Technology, Pasadena, CA, USA
2 shared publications Choonsup Lee
Jet Propulsion Laboratory, California Institute of Technology, Pasadena, CA, USA
2 shared publications
Latest Publications
- Open Access
- 1 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Microwaves
- Vol. 5 (6) , 1235-1252
Water Hunting Advanced Terahertz Spectrometer on an Ultra-Small Platform (WHATSUP)
- 1 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Microwaves
- Vol. 5 (6) , 1235-1252
Open AccessWater Hunting Advanced Terahertz Spectrometer on an Ultra-Small Platform (WHATSUP)
- 30 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Terahertz Science and Technology
- Vol. 14 (6) , 830-842
MEMS Phase Shifters for THz Beam-Scanning: Demonstration With a 500–600 GHz Phased Array With Leaky-Wave Feeds
Beam-scanning capabilities for space-borne submillimeter-wave spectrometers are critical for instrument calibration and field-of-view mapping. However, the lack of low-loss waveguide-integrated phase shifters above 500 GHz has been a significant challenge for realizing Terahertz phased array antennas. Recently developed MEMS-actuated phase shifters have emerged as promising candidates, initially demonstrating a 145 ${}^\circ$ phase shift. As a first demonstration of the efficacy of these phase shifters for electronic beam-steering, we present the design, fabrication, and characterization of a linear, near-Nyquist sampled, 4x1-element phased array operating from 500-600 GHz. The array element is a silicon micro-machined leaky-wave feed based on a Fabry-Pérot cavity to enhance directivity and reduce grating lobes while achieving bandwidth requirements with minimal scan loss. It is shown, through measurements, that this antenna feed is suitable for use in larger 8x1-element arrays for applications that require moderate gain (20 dBi) and scanning ( $\pm 20^\circ$ ) with a fan beam. Furthermore, we present measurement results of a second generation of MEMS phase shifters with an increased measured phase shift up to 350 ${}^\circ$ . A full 360 ${}^\circ$ phase-wrapping capability is desired as this will enable high-gain lens-scanning phased arrays that can be used for future submillimeter-wave spectrometers.
- 30 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Terahertz Science and Technology
- Vol. 14 (6) , 830-842
MEMS Phase Shifters for THz Beam-Scanning: Demonstration With a 500–600 GHz Phased Array With Leaky-Wave Feeds
Beam-scanning capabilities for space-borne submillimeter-wave spectrometers are critical for instrument calibration and field-of-view mapping. However, the lack of low-loss waveguide-integrated phase shifters above 500 GHz has been a significant challenge for realizing Terahertz phased array antennas. Recently developed MEMS-actuated phase shifters have emerged as promising candidates, initially demonstrating a 145 ${}^\circ$ phase shift. As a first demonstration of the efficacy of these phase shifters for electronic beam-steering, we present the design, fabrication, and characterization of a linear, near-Nyquist sampled, 4x1-element phased array operating from 500-600 GHz. The array element is a silicon micro-machined leaky-wave feed based on a Fabry-Pérot cavity to enhance directivity and reduce grating lobes while achieving bandwidth requirements with minimal scan loss. It is shown, through measurements, that this antenna feed is suitable for use in larger 8x1-element arrays for applications that require moderate gain (20 dBi) and scanning ( $\pm 20^\circ$ ) with a fan beam. Furthermore, we present measurement results of a second generation of MEMS phase shifters with an increased measured phase shift up to 350 ${}^\circ$ . A full 360 ${}^\circ$ phase-wrapping capability is desired as this will enable high-gain lens-scanning phased arrays that can be used for future submillimeter-wave spectrometers.
- 3 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Microelectromechanical Systems
- Vol. 33 (5) , 532-542
500-750 GHz Contactless Rotating MEMS Single-Pole Double-Throw Waveguide Switch
This paper presents a Single-Pole Double-Throw MEMS waveguide switch operating at $500-750~GHz$ . The switch consist of a U-bend waveguide surrounded by an electromagnetic bandgap (EBG) surface. The EBG surface is used to isolate the electromagnetic wave without mechanical or electrical contact. The U-bend is placed on a rotating arm, that moves between two positions. The arms movement is controlled by a rotating MEMS motor that can rotate $\pm 4.5^\circ$ at $70~V$ . The switch is fabricated using silicon micromachining and is designed to be in-plane with the connecting waveguides. This allows it to be implemented into a silicon micromachined waveguide network. The waveguide switch has a measured insertion loss less than $2.5~dB$ and an isolation larger than $30~dB$ between $550-750~GHz$ . Since the electromagnetic wave can be routed with the EBG surface instead of needing electrical or mechanical contact, the MEMS waveguide switch can operate without the need for mechanical contact and avoids common MEMS switch issues such as stiction between the switch and its ports. 2024-0059
- 3 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Microelectromechanical Systems
- Vol. 33 (5) , 532-542
500-750 GHz Contactless Rotating MEMS Single-Pole Double-Throw Waveguide Switch
This paper presents a Single-Pole Double-Throw MEMS waveguide switch operating at $500-750~GHz$ . The switch consist of a U-bend waveguide surrounded by an electromagnetic bandgap (EBG) surface. The EBG surface is used to isolate the electromagnetic wave without mechanical or electrical contact. The U-bend is placed on a rotating arm, that moves between two positions. The arms movement is controlled by a rotating MEMS motor that can rotate $\pm 4.5^\circ$ at $70~V$ . The switch is fabricated using silicon micromachining and is designed to be in-plane with the connecting waveguides. This allows it to be implemented into a silicon micromachined waveguide network. The waveguide switch has a measured insertion loss less than $2.5~dB$ and an isolation larger than $30~dB$ between $550-750~GHz$ . Since the electromagnetic wave can be routed with the EBG surface instead of needing electrical or mechanical contact, the MEMS waveguide switch can operate without the need for mechanical contact and avoids common MEMS switch issues such as stiction between the switch and its ports. 2024-0059
- 12 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Terahertz Science and Technology
- Vol. 14 (2) , 178-187
A Waveguide-Based Variable Attenuator for Terahertz Applications
This article presents a novel waveguide-based terahertz (THz) variable attenuator, integrated with a piezo-electric motor, to achieve precise and fine step values of signal attenuation. A low-resistivity silicon slab, coated with a thin layer of Titanium metal, is inserted inside a waveguide that absorbs some of the electromagnetic waves traveling through the guide. Impedance matching is achieved by gradually perforating the silicon slab and thus, creating variable impedance needed for matching. The amount of signal absorbed by the slab is determined by the sheet resistance value of the metal coating and the position of the slab in the waveguide. A miniature nanometer-scale precision piezo electric motor is used for precise control of the signal attenuation. In this work, we present the attenuator design for a frequency band of 500-750 GHz where up to 40 dB of signal attenuation was achieved, using a 1.75 mm long silicon slab with a 25 nm Titanium metal coating. The presented variable attenuator design offers compactness, scalability, and easy integration with THz sources and receivers. Furthermore, the compact size and low power consumption open up possibilities for implementation on CubeSat/Smallsat/Drone-based platforms, further expanding its potential space applications.
- 12 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Terahertz Science and Technology
- Vol. 14 (2) , 178-187
A Waveguide-Based Variable Attenuator for Terahertz Applications
This article presents a novel waveguide-based terahertz (THz) variable attenuator, integrated with a piezo-electric motor, to achieve precise and fine step values of signal attenuation. A low-resistivity silicon slab, coated with a thin layer of Titanium metal, is inserted inside a waveguide that absorbs some of the electromagnetic waves traveling through the guide. Impedance matching is achieved by gradually perforating the silicon slab and thus, creating variable impedance needed for matching. The amount of signal absorbed by the slab is determined by the sheet resistance value of the metal coating and the position of the slab in the waveguide. A miniature nanometer-scale precision piezo electric motor is used for precise control of the signal attenuation. In this work, we present the attenuator design for a frequency band of 500-750 GHz where up to 40 dB of signal attenuation was achieved, using a 1.75 mm long silicon slab with a 25 nm Titanium metal coating. The presented variable attenuator design offers compactness, scalability, and easy integration with THz sources and receivers. Furthermore, the compact size and low power consumption open up possibilities for implementation on CubeSat/Smallsat/Drone-based platforms, further expanding its potential space applications.