Mohammad Sami Al Khazali
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Mohammad Sami Al Khazali has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Stanislav Seitl
Brno University of Technology, Faculty of Civil Engineering, Institute of Structural Mechanics Veveří 331/95, 602 00 Brno, Czech Republic and Czech Academy of Sciences; Institute of Physics of Materials, v. v. i., Žižkova 22, 616 00 Brno, Czech Republic
7 shared publications - Lucie Malíková
Brno University of Technology, Faculty of Civil Engineering, Institute of Structural Mechanics Veveří 331/95, 602 00 Brno, Czech Republic and Czech Academy of Sciences; Institute of Physics of Materials, v. v. i., Žižkova 22, 616 00 Brno, Czech Republic
6 shared publications - Grzegorz Lesiuk
Faculty of Mechanical Engineering, Wroclaw University of Science and Technology, 50-370 Wroclaw, Poland
4 shared publications - Dziuba Szymon
Faculty of Mechanical Engineering, Wroclaw University of Science and Technology , Łukasiewicza 5/7, 50-370 Wrocław , Poland
3 shared publications - Miroslav Vacek
VŠB-TU Ostrava, Faculty of Civil Engineering, Ludvíka Podéště 1875, 708 33 Ostrava, Czech Republic
3 shared publications - Kamila Kozáková
Faculty of Mechanical Engineering, Brno University of Technology, Technická 289/2, 616 69 Brno, Czech Republic; Institute of Physics of Materials, Czech Academy of Sciences, Žižkova 513/22, 616 00 Brno, Czech Republic
2 shared publications
Latest Publications
- Open Access
- 22 July 2026
- Published by Elsevier in SSRN Electronic Journal
Microscopic Evaluation of Fatigue Damage Development in Welded S460 Steel Specimens after Accelerated Corrosion Exposure
The present study investigates the development of fatigue damage in welded S460 high-strength steel specimens subjected to different corrosion exposure conditions. Four surface conditions were considered: an uncorroded reference condition, 3-day exposure, 6-day exposure and combined 6+3-day exposure, hereafter referred to as 3D, 6D and 6+3D/9D, respectively. Fatigue tests were performed at a stress ratio of . Microscopic observations were carried out before and after fatigue testing using an Olympus DSX1000 digital microscope to evaluate surface degradation, crack/fracture localization and damage development in the welded region. The uncorroded reference condition showed fatigue damage that was predominantly localized in the welded region, thereby confirming the dominant role of weld geometry and the local notch effect. As the level of corrosion exposure increased, the surface condition changed progressively. The 3D condition exhibited limited early degradation, the 6D condition revealed more distinct surface defects, and the 6+3D/9D condition showed the most pronounced corrosion-product regions and pit-like surface damage. The fatigue results indicated a non-monotonic influence of corrosion exposure. The apparent improvement observed for the 3D and 6D conditions may be related to local modification of the weld-toe surface condition and partial mitigation of the original weld-induced notch effect. After fatigue testing, all representative specimens showed crack/fracture development near the weld toe and heat-affected zone (HAZ) vicinity. The findings indicate that fatigue damage was governed by the combined effect of weld-toe geometry, the visually distinguishable HAZ vicinity and corrosion-induced surface degradation.
- 22 July 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessMicroscopic Evaluation of Fatigue Damage Development in Welded S460 Steel Specimens after Accelerated Corrosion Exposure
The present study investigates the development of fatigue damage in welded S460 high-strength steel specimens subjected to different corrosion exposure conditions. Four surface conditions were considered: an uncorroded reference condition, 3-day exposure, 6-day exposure and combined 6+3-day exposure, hereafter referred to as 3D, 6D and 6+3D/9D, respectively. Fatigue tests were performed at a stress ratio of . Microscopic observations were carried out before and after fatigue testing using an Olympus DSX1000 digital microscope to evaluate surface degradation, crack/fracture localization and damage development in the welded region. The uncorroded reference condition showed fatigue damage that was predominantly localized in the welded region, thereby confirming the dominant role of weld geometry and the local notch effect. As the level of corrosion exposure increased, the surface condition changed progressively. The 3D condition exhibited limited early degradation, the 6D condition revealed more distinct surface defects, and the 6+3D/9D condition showed the most pronounced corrosion-product regions and pit-like surface damage. The fatigue results indicated a non-monotonic influence of corrosion exposure. The apparent improvement observed for the 3D and 6D conditions may be related to local modification of the weld-toe surface condition and partial mitigation of the original weld-induced notch effect. After fatigue testing, all representative specimens showed crack/fracture development near the weld toe and heat-affected zone (HAZ) vicinity. The findings indicate that fatigue damage was governed by the combined effect of weld-toe geometry, the visually distinguishable HAZ vicinity and corrosion-induced surface degradation.
- Open Access
- 11 June 2026
- Published by Elsevier in SSRN Electronic Journal
Microscopic Evaluation of Fatigue Damage Development in Welded S460 Steel Specimens after Accelerated Corrosion Exposure
The present study investigates the development of fatigue damage in welded S460 high-strength steel specimens subjected to different corrosion exposure conditions. Four surface conditions were considered: an uncorroded reference condition, 3-day exposure, 6-day exposure and combined 6+3-day exposure, hereafter referred to as 3D, 6D and 6+3D/9D, respectively. Fatigue tests were performed at a stress ratio of . Microscopic observations were carried out before and after fatigue testing using an Olympus DSX1000 digital microscope to evaluate surface degradation, crack/fracture localization and damage development in the welded region.The uncorroded reference condition showed fatigue damage that was predominantly localized in the welded region, thereby confirming the dominant role of weld geometry and the local notch effect. As the level of corrosion exposure increased, the surface condition changed progressively. The 3D condition exhibited limited early degradation, the 6D condition revealed more distinct surface defects, and the 6+3D/9D condition showed the most pronounced corrosion-product regions and pit-like surface damage. The fatigue results indicated a non-monotonic influence of corrosion exposure. The apparent improvement observed for the 3D and 6D conditions may be related to local modification of the weld-toe surface condition and partial mitigation of the original weld-induced notch effect.After fatigue testing, all representative specimens showed crack/fracture development near the weld toe and heat-affected zone (HAZ) vicinity. The findings indicate that fatigue damage was governed by the combined effect of weld-toe geometry, the visually distinguishable HAZ vicinity and corrosion-induced surface degradation.
- 11 June 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessMicroscopic Evaluation of Fatigue Damage Development in Welded S460 Steel Specimens after Accelerated Corrosion Exposure
The present study investigates the development of fatigue damage in welded S460 high-strength steel specimens subjected to different corrosion exposure conditions. Four surface conditions were considered: an uncorroded reference condition, 3-day exposure, 6-day exposure and combined 6+3-day exposure, hereafter referred to as 3D, 6D and 6+3D/9D, respectively. Fatigue tests were performed at a stress ratio of . Microscopic observations were carried out before and after fatigue testing using an Olympus DSX1000 digital microscope to evaluate surface degradation, crack/fracture localization and damage development in the welded region.The uncorroded reference condition showed fatigue damage that was predominantly localized in the welded region, thereby confirming the dominant role of weld geometry and the local notch effect. As the level of corrosion exposure increased, the surface condition changed progressively. The 3D condition exhibited limited early degradation, the 6D condition revealed more distinct surface defects, and the 6+3D/9D condition showed the most pronounced corrosion-product regions and pit-like surface damage. The fatigue results indicated a non-monotonic influence of corrosion exposure. The apparent improvement observed for the 3D and 6D conditions may be related to local modification of the weld-toe surface condition and partial mitigation of the original weld-induced notch effect.After fatigue testing, all representative specimens showed crack/fracture development near the weld toe and heat-affected zone (HAZ) vicinity. The findings indicate that fatigue damage was governed by the combined effect of weld-toe geometry, the visually distinguishable HAZ vicinity and corrosion-induced surface degradation.
- 2 June 2026
- Published by Springer Nature
- p. 346-356
Fatigue Performance of S460 High-Strength Steel Welded Joints: Experimental and Numerical Approaches
- 2 June 2026
- Published by Springer Nature
- p. 346-356
Fatigue Performance of S460 High-Strength Steel Welded Joints: Experimental and Numerical Approaches
- Open Access
- 5 April 2026
- Published by Gruppo Italiano Frattura in Fracture and Structural Integrity
- Vol. 20 (77) , 56-77
Effect of Corrosion Damage on the Fatigue Behavior of S460NL High-Strength Steel under Cyclic Loading
The present study investigates the influence of corrosion exposure on the fatigue behavior of S460NL high-strength structural steel, a material that is frequently utilized in offshore and civil engineering structures. Accelerated corrosion was simulated under controlled laboratory conditions for exposure periods of 3 days, 6 days, and 6 + 3 days, in addition to specimens subjected to natural atmospheric corrosion. To this end, fatigue tests were performed to obtain S–N curves, and the results were evaluated using Basquin's law and the probabilistic Castillo–Canteli model. The findings indicate that corrosion has a substantial impact on fatigue resistance. The endurance limit exhibited a decline from 214 MPa for the reference specimens to 176 MPa following three days of corrosion, 135 MPa after six days, and approximately 92 MPa after combined corrosion exposure, signifying a reduction of up to 57%. Fractographic observations revealed that corrosion pits act as stress concentrators, thereby promoting early crack initiation. A discernible correlation was identified between corrosion mass loss and normalized endurance limit. These findings highlight the importance of considering corrosion effects in fatigue life assessment and structural design of high-strength steel components.
- 5 April 2026
- Published by Gruppo Italiano Frattura in Fracture and Structural Integrity
- Vol. 20 (77) , 56-77
Open AccessEffect of Corrosion Damage on the Fatigue Behavior of S460NL High-Strength Steel under Cyclic Loading
The present study investigates the influence of corrosion exposure on the fatigue behavior of S460NL high-strength structural steel, a material that is frequently utilized in offshore and civil engineering structures. Accelerated corrosion was simulated under controlled laboratory conditions for exposure periods of 3 days, 6 days, and 6 + 3 days, in addition to specimens subjected to natural atmospheric corrosion. To this end, fatigue tests were performed to obtain S–N curves, and the results were evaluated using Basquin's law and the probabilistic Castillo–Canteli model. The findings indicate that corrosion has a substantial impact on fatigue resistance. The endurance limit exhibited a decline from 214 MPa for the reference specimens to 176 MPa following three days of corrosion, 135 MPa after six days, and approximately 92 MPa after combined corrosion exposure, signifying a reduction of up to 57%. Fractographic observations revealed that corrosion pits act as stress concentrators, thereby promoting early crack initiation. A discernible correlation was identified between corrosion mass loss and normalized endurance limit. These findings highlight the importance of considering corrosion effects in fatigue life assessment and structural design of high-strength steel components.
- Open Access
- 1 January 2026
- Published by Walter de Gruyter GmbH in Journal of the Mechanical Behavior of Materials
- Vol. 35 (1)
Comparative evaluation of fatigue crack propagation in high-strength steels S460, S690, and S960 using optical and CMOD methods at stress ratio R = 0.1
The present study compares the fatigue crack propagation behavior of three high-strength steels – S460, S690, and S960 – tested at a stress ratio R = 0.1 and at room temperature. The measurement of fatigue crack growth was accomplished through the implementation of two complementary techniques. The first technique involved the assessment of crack mouth opening displacement (CMOD), which was recorded using a clip gauge on an MTS 100 kN testing machine. The second technique entailed the use of an optical crack tracking resonant electromagnetic pulsator Amsler 20 HFP 5100. The material characterization process entailed the execution of tensile testing, Vickers hardness measurements, and microstructural analysis. The propagation rates of fatigue cracks were evaluated using Paris-law fitting, which revealed that S460 exhibited the lowest crack growth rate, followed by S690 and S960. Scanning electron microscopy (SEM) was utilized to confirm the presence of Mode I fatigue striations in all materials. The novelty of the work lies in the controlled replicate-specimen comparison of three HSS grades under identical CT geometry, stress ratio, laboratory conditions, and Paris-law evaluation procedure, while transparently defining the CMOD–optical comparison as a method-aware comparison rather than a simultaneous within-specimen validation.
- 1 January 2026
- Published by Walter de Gruyter GmbH in Journal of the Mechanical Behavior of Materials
- Vol. 35 (1)
Open AccessComparative evaluation of fatigue crack propagation in high-strength steels S460, S690, and S960 using optical and CMOD methods at stress ratio R = 0.1
The present study compares the fatigue crack propagation behavior of three high-strength steels – S460, S690, and S960 – tested at a stress ratio R = 0.1 and at room temperature. The measurement of fatigue crack growth was accomplished through the implementation of two complementary techniques. The first technique involved the assessment of crack mouth opening displacement (CMOD), which was recorded using a clip gauge on an MTS 100 kN testing machine. The second technique entailed the use of an optical crack tracking resonant electromagnetic pulsator Amsler 20 HFP 5100. The material characterization process entailed the execution of tensile testing, Vickers hardness measurements, and microstructural analysis. The propagation rates of fatigue cracks were evaluated using Paris-law fitting, which revealed that S460 exhibited the lowest crack growth rate, followed by S690 and S960. Scanning electron microscopy (SEM) was utilized to confirm the presence of Mode I fatigue striations in all materials. The novelty of the work lies in the controlled replicate-specimen comparison of three HSS grades under identical CT geometry, stress ratio, laboratory conditions, and Paris-law evaluation procedure, while transparently defining the CMOD–optical comparison as a method-aware comparison rather than a simultaneous within-specimen validation.
- Open Access
- 26 February 2025
- Published by Periodica Polytechnica Budapest University of Technology and Economics in Periodica Polytechnica Civil Engineering
- Vol. 69 (2) , 611-620
Failure Analysis of Mortar Specimens with a Hexagonal Honeycomb Panel during Fatigue Load
It has been published in recent research studies that several mechanical properties of mortar reinforced with suitably spatial shaped plastic elements can be improved. Thus, a hexagonal geometric shape was chosen due to its high rigidity for this study. Stress distribution at a bi-material interface between a polymer part reinforcing a mortar specimen and the rest of the mortar part has been investigated to explain fatigue fracture behavior of rectangular specimens tested. A three-point-bending (3PB) test was simulated via a finite element method (FEM) considering several simplifications, and various heights of the polymer reinforcement were modeled to investigate its influence on stress redistribution. For comparison, a pure mortar specimen without any plastic elements was considered the reference. The numerical results obtained are discussed and compared to the experimental ones. Within the experimental campaign, bulk density, static properties and fatigue characteristics were tested, analyzed and discussed. Improvements in flexural strength were observed when the plastic panel was used as reinforcement, which agrees with other scientific works. Directions for future research were identified.
- 26 February 2025
- Published by Periodica Polytechnica Budapest University of Technology and Economics in Periodica Polytechnica Civil Engineering
- Vol. 69 (2) , 611-620
Open AccessFailure Analysis of Mortar Specimens with a Hexagonal Honeycomb Panel during Fatigue Load
It has been published in recent research studies that several mechanical properties of mortar reinforced with suitably spatial shaped plastic elements can be improved. Thus, a hexagonal geometric shape was chosen due to its high rigidity for this study. Stress distribution at a bi-material interface between a polymer part reinforcing a mortar specimen and the rest of the mortar part has been investigated to explain fatigue fracture behavior of rectangular specimens tested. A three-point-bending (3PB) test was simulated via a finite element method (FEM) considering several simplifications, and various heights of the polymer reinforcement were modeled to investigate its influence on stress redistribution. For comparison, a pure mortar specimen without any plastic elements was considered the reference. The numerical results obtained are discussed and compared to the experimental ones. Within the experimental campaign, bulk density, static properties and fatigue characteristics were tested, analyzed and discussed. Improvements in flexural strength were observed when the plastic panel was used as reinforcement, which agrees with other scientific works. Directions for future research were identified.
- Open Access
- 11 October 2024
- Published by Gruppo Italiano Frattura in Fracture and Structural Integrity
- Vol. 19 (71) , 67-79
Determination of the geometric parameters of the defects based on the tomographically obtained data and their influence on the fatigue behavior of the S960 with laser cladded protective layers
This article deals with identifying defects of layered high strength steel materials with the help of tomography measurement. Test samples were made of S960 High Strength Steel to which layers of either aluminium bronze, hardchrome, cobalt alloy or stainless steel were applied by a laser cladding technology. The experimental campaign included a study of morphometric parameters of internal defects in and near the bi-material interface region using X-ray micro-tomography and their potential influence on the fatigue behavior during a three-point bending test.
- 11 October 2024
- Published by Gruppo Italiano Frattura in Fracture and Structural Integrity
- Vol. 19 (71) , 67-79
Open AccessDetermination of the geometric parameters of the defects based on the tomographically obtained data and their influence on the fatigue behavior of the S960 with laser cladded protective layers
This article deals with identifying defects of layered high strength steel materials with the help of tomography measurement. Test samples were made of S960 High Strength Steel to which layers of either aluminium bronze, hardchrome, cobalt alloy or stainless steel were applied by a laser cladding technology. The experimental campaign included a study of morphometric parameters of internal defects in and near the bi-material interface region using X-ray micro-tomography and their potential influence on the fatigue behavior during a three-point bending test.