SQSaidabdullo Qurbonalizoda

Saidabdullo Qurbonalizoda

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Saidabdullo Qurbonalizoda has a total of 11 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Impact of Inducer Tip Clearance on Cryopump Performance

    by Sunwuji Wang, Xiaomei Guo, Ping Li, Zuchao Zhu, Aminjon Gulakhmadov, Saidabdullo Qurbonalizoda

    Inducers play a critical role in pump operation by providing a preliminary pressure boost to suppress cavitation. The size of the tip clearance directly influences a pump’s operational efficiency. To investigate the impact of tip clearance on a pump’s hydraulic performance and its behavior under cavitation conditions, this study combines experimental and numerical simulation approaches. Numerical computations of the full flow field, including the inducer and a two-stage impeller, were performed for five liquefied natural gas (LNG) cryogenic inducers with different tip clearances. The accuracy of the numerical simulation results was validated by comparing them with the experimentally obtained hydraulic performance curves. The results yield cavitation performance curves, pressure distributions at incipient cavitation, vapor volume fraction contours, and leakage flow streamlines for various tip clearances. The impact of tip clearance on the overall hydraulic performance and cavitation behavior of the LNG inducer was systematically examined, with particular attention given to the microscopic evolution of the Tip Leakage Vortex (TLV) during the initial stages of cavitation. The experimental results indicate that for every 0.2 mm increase in the inducer tip clearance, the pump head decreases by approximately 1 m, the efficiency drops by about 0.2%, and the tip leakage flow rate increases by approximately 5 m3/h. Furthermore, under cavitation conditions, the cavitation area expands as the tip clearance increases. A critical clearance value, δ, exists within the range of 0.4 mm to 0.6 mm, which governs the development pattern of the TLV. When the clearance is smaller than δ, the TLV forms more rapidly, and cavitation development is significantly more sensitive to increases in tip clearance. Conversely, when the clearance exceeds δ, the formation of the TLV is delayed, and cavitation progression becomes less responsive to further increases in tip clearance.

  • Open Access

    Impact of Inducer Tip Clearance on Cryopump Performance

    by Wuji Wangsun, Xiaomei Guo, Ping Li, Zuchao Zhu, Aminjon Gulakhmadov, Saidabdullo Qurbonalizoda

    To investigate the influence of different tip clearances on the hydraulic performance and cavitation characteristics of a cryogenic inducer, this study builds upon previous research by employing the SST k-ω turbulence model and modifying the empirical coefficients for evaporation and condensation in the Zwart cavitation model. Numerical simulations of the full flow field within an LNG cryogenic inducer were conducted. The results yielded cavitation performance curves, pressure distributions at incipient cavitation, vapor volume fraction contours, and leakage flow streamlines for various tip clearances. The impact of tip clearance on the overall hydraulic performance and cavitation behavior of the LNG inducer was systematically examined, with particular attention given to the microscopic evolution of the Tip Leakage Vortex (TLV) during the initial stages of cavitation. Experimental findings indicate that as the tip clearance increases, the tip leakage flow intensifies, leading to greater energy losses within the inducer and a consequent slight reduction in pump head and efficiency. A critical clearance value, δ, exists within the range of 0.4 mm to 0.6 mm, which governs the development pattern of the TLV. When the clearance is smaller than δ, the TLV forms more rapidly, and cavitation development is significantly more sensitive to increases in tip clearance. Conversely, when the clearance exceeds δ, the formation of the TLV is delayed, and cavitation progression becomes less responsive to further increases in tip clearance.

  • Open Access

    Research on Electrical Properties of the Cutting Zone in Cutting Metal/Insulation Materials

    by Bohua Feng, Chen Yang, Qianying Zhou, Xiaomei Guo, Qurbonalizoda Saidabdullo Shamsullo, Gaoan Zheng, Zeqi Tong, Xuefeng Xu

    The cutting process is accompanied by complex electrical phenomena, which are particularly evident in narrow cutting clearances. To further explore the laws of electrical phenomena in the capillary of the cutting zone, this paper uses a Faraday collector with an external bias electric field to investigate the electrical phenomena in the narrow slit of the cutting zone under different cutting parameters and when different tool and workpiece materials are combined. The results show that there is a stable and continuous electrical phenomenon in the cutting contact area, and the emission intensity of charged particles when cutting insulating materials is significantly higher than that of metals. The emission intensity of negative ions is higher than that of positive ions. The electrical and mechanical properties of materials have a significant impact on the electrical phenomena in the cutting zone. In addition, it was found that there is a linear relationship between the electrical phenomena in the cutting zone and the cutting parameters. Finally, based on the morphology of the capillaries in the cutting zone, the self-excited electric field intensity generated in it during the cutting process was estimated.