Sunwuji Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Sunwuji Wang has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Aminjon Gulakhmadov
Institute of Water Problems, Hydropower and Ecology of the National Academy of Sciences of Tajikistan Dushanbe Tajikistan
2 shared publications - Ping Li
Dalian LEO Huaneng Pump Co., Ltd., Dalian 116041, China
2 shared publications - Saidabdullo Qurbonalizoda
National Academy of Sciences of Tajikistan Center of Innovative Development of Science and New Technologies, Dushanbe 734002, Tajikistan
2 shared publications - Xiaomei Guo
Key Laboratory of Key Technologies for Mechanical Industry Hydroelectric Power Generation Pump Turbine, Zhejiang Key Laboratory of Pumps and Turbines, Zhejiang University of Water Resource and Electric Power, Hangzhou 310018, China
2 shared publications - Zuchao Zhu
Key Laboratory of Fluid Transmission Technology of Zhejiang Province, Zhejiang Sci-Tech University 1 , Hangzhou 310018
2 shared publications
Latest Publications
- Open Access
Impact of Inducer Tip Clearance on Cryopump Performance
Inducers play a critical role in pump operation by providing a preliminary pressure boost to suppress cavitation. The size of the tip clearance directly influences a pump’s operational efficiency. To investigate the impact of tip clearance on a pump’s hydraulic performance and its behavior under cavitation conditions, this study combines experimental and numerical simulation approaches. Numerical computations of the full flow field, including the inducer and a two-stage impeller, were performed for five liquefied natural gas (LNG) cryogenic inducers with different tip clearances. The accuracy of the numerical simulation results was validated by comparing them with the experimentally obtained hydraulic performance curves. The results yield cavitation performance curves, pressure distributions at incipient cavitation, vapor volume fraction contours, and leakage flow streamlines for various tip clearances. The impact of tip clearance on the overall hydraulic performance and cavitation behavior of the LNG inducer was systematically examined, with particular attention given to the microscopic evolution of the Tip Leakage Vortex (TLV) during the initial stages of cavitation. The experimental results indicate that for every 0.2 mm increase in the inducer tip clearance, the pump head decreases by approximately 1 m, the efficiency drops by about 0.2%, and the tip leakage flow rate increases by approximately 5 m3/h. Furthermore, under cavitation conditions, the cavitation area expands as the tip clearance increases. A critical clearance value, δ, exists within the range of 0.4 mm to 0.6 mm, which governs the development pattern of the TLV. When the clearance is smaller than δ, the TLV forms more rapidly, and cavitation development is significantly more sensitive to increases in tip clearance. Conversely, when the clearance exceeds δ, the formation of the TLV is delayed, and cavitation progression becomes less responsive to further increases in tip clearance.
Open AccessImpact of Inducer Tip Clearance on Cryopump Performance
Inducers play a critical role in pump operation by providing a preliminary pressure boost to suppress cavitation. The size of the tip clearance directly influences a pump’s operational efficiency. To investigate the impact of tip clearance on a pump’s hydraulic performance and its behavior under cavitation conditions, this study combines experimental and numerical simulation approaches. Numerical computations of the full flow field, including the inducer and a two-stage impeller, were performed for five liquefied natural gas (LNG) cryogenic inducers with different tip clearances. The accuracy of the numerical simulation results was validated by comparing them with the experimentally obtained hydraulic performance curves. The results yield cavitation performance curves, pressure distributions at incipient cavitation, vapor volume fraction contours, and leakage flow streamlines for various tip clearances. The impact of tip clearance on the overall hydraulic performance and cavitation behavior of the LNG inducer was systematically examined, with particular attention given to the microscopic evolution of the Tip Leakage Vortex (TLV) during the initial stages of cavitation. The experimental results indicate that for every 0.2 mm increase in the inducer tip clearance, the pump head decreases by approximately 1 m, the efficiency drops by about 0.2%, and the tip leakage flow rate increases by approximately 5 m3/h. Furthermore, under cavitation conditions, the cavitation area expands as the tip clearance increases. A critical clearance value, δ, exists within the range of 0.4 mm to 0.6 mm, which governs the development pattern of the TLV. When the clearance is smaller than δ, the TLV forms more rapidly, and cavitation development is significantly more sensitive to increases in tip clearance. Conversely, when the clearance exceeds δ, the formation of the TLV is delayed, and cavitation progression becomes less responsive to further increases in tip clearance.
- Open Access
- 26 November 2025
- Published by MDPI AG in Preprints.org
Impact of Inducer Tip Clearance on Cryopump Performance
To investigate the influence of different tip clearances on the hydraulic performance and cavitation characteristics of a cryogenic inducer, this study builds upon previous research by employing the SST k-ω turbulence model and modifying the empirical coefficients for evaporation and condensation in the Zwart cavitation model. Numerical simulations of the full flow field within an LNG cryogenic inducer were conducted. The results yielded cavitation performance curves, pressure distributions at incipient cavitation, vapor volume fraction contours, and leakage flow streamlines for various tip clearances. The impact of tip clearance on the overall hydraulic performance and cavitation behavior of the LNG inducer was systematically examined, with particular attention given to the microscopic evolution of the Tip Leakage Vortex (TLV) during the initial stages of cavitation. Experimental findings indicate that as the tip clearance increases, the tip leakage flow intensifies, leading to greater energy losses within the inducer and a consequent slight reduction in pump head and efficiency. A critical clearance value, δ, exists within the range of 0.4 mm to 0.6 mm, which governs the development pattern of the TLV. When the clearance is smaller than δ, the TLV forms more rapidly, and cavitation development is significantly more sensitive to increases in tip clearance. Conversely, when the clearance exceeds δ, the formation of the TLV is delayed, and cavitation progression becomes less responsive to further increases in tip clearance.
- 26 November 2025
- Published by MDPI AG in Preprints.org
Open AccessImpact of Inducer Tip Clearance on Cryopump Performance
To investigate the influence of different tip clearances on the hydraulic performance and cavitation characteristics of a cryogenic inducer, this study builds upon previous research by employing the SST k-ω turbulence model and modifying the empirical coefficients for evaporation and condensation in the Zwart cavitation model. Numerical simulations of the full flow field within an LNG cryogenic inducer were conducted. The results yielded cavitation performance curves, pressure distributions at incipient cavitation, vapor volume fraction contours, and leakage flow streamlines for various tip clearances. The impact of tip clearance on the overall hydraulic performance and cavitation behavior of the LNG inducer was systematically examined, with particular attention given to the microscopic evolution of the Tip Leakage Vortex (TLV) during the initial stages of cavitation. Experimental findings indicate that as the tip clearance increases, the tip leakage flow intensifies, leading to greater energy losses within the inducer and a consequent slight reduction in pump head and efficiency. A critical clearance value, δ, exists within the range of 0.4 mm to 0.6 mm, which governs the development pattern of the TLV. When the clearance is smaller than δ, the TLV forms more rapidly, and cavitation development is significantly more sensitive to increases in tip clearance. Conversely, when the clearance exceeds δ, the formation of the TLV is delayed, and cavitation progression becomes less responsive to further increases in tip clearance.