THTadashi Hatano

Tadashi Hatano

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Tadashi Hatano has a total of 17 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Soft x-ray laminar-type varied-line-spacing multilayer spherical diffraction grating designed for a flat-field grating spectrograph with enhanced spectral flux in the 1–2 keV region

    by T. Hatano, A. Sagisaka, M. Koike, M. Terauchi, A. S. Pirozhkov

    A soft x-ray diffraction grating with an aperiodic multilayer coating was designed to enhance spectral flux in a photon energy range of 1–2 keV by means of numerical calculation. Optimized groove depth and angle of incidence were 2.65 nm and 87.50°, respectively, for the grating with a groove density of 2400 lines/mm. The optimum number of W/B4C layer pairs was 6; the thicknesses of four bottom B4C layers were constant, and those of two top layers were unequal, while all W layer thicknesses were the same. An additional top layer of Au was crucial to provide uniform diffraction efficiency across the spectral range. In the region of 1–2 keV, the calculated diffraction efficiency of the designed gratings was ∼4.4% on average, and the calculated spectral flux (which correlates with analytical sensitivity) was 2.8 times larger than that of a previously designed Au-coated grating with an angle of incidence of 88.65°. The designed grating was manufactured; its measured diffraction efficiency was close to the calculated one in the 0.6–1.4 keV and >2 keV spectral ranges but somewhat lower in the 1.6–1.8 keV range. The spectrograph equipped with the new grating exhibited resolving power exceeding 400, which approached the pixel-size limit.

  • Design of soft x-ray high diffraction efficiency and spectral flux Au/Ni bilayer coated laminar-type diffraction grating for objective soft x-ray flat-field spectrograph in a region of 250–550 eV

    by M. Koike, T. Hatano, A. S. Pirozhkov, T. Murano, Y. Oue, S. Koshiya, T. Kakio, K. Kondo, M. Terauchi

    An objective soft x-ray flat-field spectrograph employing a laminar-type bilayer coated, varied-line-spacing, spherical grating was designed to improve the detection limit and sensitivity of soft x-ray flat-field spectrographs in a region of 250–550 eV. As a design criterion, spectral flux, SF, [Hatano et al., Appl. Opt. 60, 4993–4999 (2021)], which is proportional to the amount of optical flux incident onto a detector and correlated with detection sensitivity, was used to be maximized. To enhance reflectivity with the coating design, Au/Ni bilayer coating was investigated to optimize the incidence angle and thickness of the Ni layer. This is based on the consideration that, in an energy region of over 400 eV, refractive indices of Au (bottom layer), Ni (top layer), and vacuum are increased from the bottom to the top of the layers, and a supplemental enhancement of reflectivity can be expected by optimizing the thickness of the top layer. Thus, the thickness of Ni and the incidence angle were chosen to be 8.0 nm and 86.00°, respectively. To maintain dispersion and spectral resolution of the grating used at an incidence angle of 87.07° as previously designed, groove density was increased to 1500 lines/mm from 1200 lines/mm of our previous design. Finally, a holographic, varied-line-spacing, spherical grating was designed assuming an aspherical-wavefront-recording configuration. The numerical simulation results showed that the spectrograph employing newly designed grating with laminar-type grooves and Au/Ni bilayer coating exhibited 2–18 times higher spectral flux as well as an improved spectral resolution compared with those obtained with the previously designed gratings and spectrographs.

  • Soft x-ray high diffraction efficiency and spectral flux laminar-type W/B4C multilayer diffraction grating for 300–1000 eV

    by M. Koike, T. Hatano, A. S. Pirozhkov, Y. Oue, T. Murano, T. Kakio, S. Koshiya, K. Kondo, M. Terauchi

    Multilayer diffraction gratings are designed to improve the detection limit and sensitivity of soft x-ray flat-field spectrographs in the region of 300–1000 eV, placing emphasis on Fe-L (705 eV), Cu-L (930 eV), and Zn-L (1012 eV) emissions. For this purpose, spectral flux was used as the performance index, which is proportional to the amount of optical flux incident into a detector and correlated with detection sensitivity. A super-mirror-type W/B4C multilayer coating [Koike et al., Rev.Sci. Instrum. 94, 045109 (2023)] was employed to improve diffraction efficiency in a wide energy region. The unique feature of the multilayer structure is that the average refractive index and the period length of W/B4C layer pairs are increased from the bottom to top layers. In addition, the incidence angle was reduced to 86.03° from 88.65° and the nominal groove density was increased to 3200 lines/mm from 2400 lines/mm of our previous design, to improve spectral flux while maintaining dispersion and spectral resolution. A holographic varied-line-spacing spherical grating and a soft x-ray flat-field spectrograph were designed, using the aspherical-wavefront-recording method, assuming the nominal grating constant and incident angle described above. The numerical simulation results showed that the spectrograph employing the newly designed grating with the W/B4C multilayer indicated 3.2–8.2 times higher spectral flux compared with those using the previously designed grating while keeping the same spectral resolution.


  • Open Access

    Design of soft x-ray varied-line-spacing (VLS) high-dispersion laminar-type grating coated with super-mirror-type (SMT) multilayer for flat-field spectrograph in a region of 2–4 keV

    by M. Koike, T. Hatano, A. S. Pirozhkov, Y. Ueno, M. Terauchi

    A soft x-ray varied-line-spacing (VLS) laminar-type spherical grating with a super-mirror-type (SMT) multilayer was designed for a soft x-ray high resolution flat-field spectrograph in a region of 2–4 keV. The effective groove density of the designed VLS grating is 3200 lines/mm, and the local groove density varies from 2700 to 3866 lines/mm. The geometrical imaging property was evaluated by numerical calculations. The resolving power estimated by means of ray tracing was up to ∼103. For the evaluation of diffraction efficiency, the SMT multilayer structure designed for 3200 lines/mm in our previous work, Koike et al., Rev. Sci. Instrum. 94, 045109 (2023), was employed, and the numerical calculation was performed considering the local groove density of VLS grooves and the local incidence angle being affected by the curvature of the spherical surface and the geometrical relation between the source and incidence point on the grating. The results showed that the SMT multilayer-coated grating exhibited about an order of magnitude higher diffraction efficiency compared with an Au-coated grating.


  • Open Access

    Design of soft x-ray laminar-type gratings coated with supermirror-type multilayer to enhance diffraction efficiency in a region of 2–4 keV

    by M. Koike, T. Hatano, A. S. Pirozhkov, Y. Ueno, M. Terauchi

    Soft x-ray diffraction gratings coated with a supermirror-type multilayer were designed to enhance diffraction efficiency in the energy range of 2–4 keV by means of numerical calculations. The optimized groove depth and incidence angle are 2.05 nm and 88.65°, respectively, for the grating having a groove density of 3200 grooves/mm. Regarding the multilayer structure, the optimum number of B4C/W layers pair was 11 and the thickness of B4C was increased from bottom to top, while that of W was kept constant. The replacement of the top layer of W by either Co, Cr, or Ni was an effective means of obtaining uniform diffraction efficiency. In the region of 2–4 keV, the calculated diffraction efficiency of the designed gratings was up to ∼5.3%, on average, and almost eight times larger than that of ∼0.7% of an Au coated grating.


  • Design and experimental evaluation of enhanced diffraction efficiency of lanthanum-based material coated laminar-type gratings in the boron K-emission region

    by Tadashi Hatano, Masato Koike, Masami Terauchi, Alexander S. Pirozhkov, Nobukazu Hayashi, Hiroyuki Sasai, Tetsuya Nagano

    Numerical and experimental studies have been performed to evaluate the enhancement of diffraction efficiency of diffraction gratings around B K -emission by overcoating lanthanum series layers on conventional metal-coated laminar-type gratings. We propose an optical design method based on the concept of spectral flux given by collection efficiency and diffraction efficiency. A diffraction grating with a small angle of incidence provides an advantage to soft x-ray spectrographs because it collects the emission at a larger solid angle compared to that of conventional grazing incidence diffraction gratings. Numerical calculations indicated that La and L a F 3 were promising as overcoating materials on a laminar-type Ni-coated diffraction grating, and we performed an experimental study using L a F 3 and La/C overcoatings, considering their producibility and durability. The diffraction efficiencies were measured using a reflectometer at a synchrotron facility. The diffraction efficiencies observed at 183.4 eV were 29.4% and 34.3% at angles of incidence of 85.1° and 84.9° for N i / L a F 3 and Ni/La/C gratings, respectively.