Xu Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Xu Zhang has a total of 48 co-authors. Here are the top co-authors by number of shared publications:
- Li Ran
State Key Laboratory of Power Transmission Equipment Technology, School of Electrical Engineering, Chongqing University, Chongqing, China
7 shared publications - Phillip Andrew Mawby
Warwick University
5 shared publications - Jinxiao Wei
Anhui Province Key Laboratory of Semiconductor Packaging and Reliability, Hefei University of Technology, Hefei, China
4 shared publications Wenyuan Li
Beijing Institute of Smart Energy, Beijing, China
4 shared publicationsChengxing Lian
School of Engineering Imperial College London London UK
3 shared publications- Haiyong Wan
School of Engineering, The University of Warwick, Coventry, U.K.
3 shared publications
Latest Publications
- 12 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41 (5) , 7355-7369
Dual-Mode Thermal Management of a Power Module for Normal and Short-Term Overcurrent Operation
Integrating phase change material (PCM) in a power module could mitigate the temperature surge during short-term overcurrent (OC). However, PCM in the path of heat conduction could impede cooling in normal operation. This article proposes a dual-mode thermal management approach for a three-dimensional loop packaging design of a half-bridge SiC mosfet power module, in which the PCM is placed away from the primary heat conduction path and is only activated by the OC. This offers thermal buffering during OC without notably increasing the steady-state thermal resistance. Chip temperatures of the upper and lower legs, on the two sides of the PCM, are almost equal and consistent with values in a package without PCM. The 1200 V, 80 A prototype is shown to have superior performance to a conventional module with single-sided cooling. Testing under 3 p.u. and 10 s OC shows that integrating PCM can reduce the chip temperature rise by about 11°C. The PCM thermal buffering effect in repetitive transients is demonstrated and evaluated. Double pulse testing shows improved switching characteristics. The parasitic loop inductance is measured to be 5.67 and 7 nH in static and dynamic conditions, respectively, and the simulated value is 5.25 nH. Thermal cycling results confirm the proposed module's reliability comparable to the conventional double-sided design.
- 12 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41 (5) , 7355-7369
Dual-Mode Thermal Management of a Power Module for Normal and Short-Term Overcurrent Operation
Integrating phase change material (PCM) in a power module could mitigate the temperature surge during short-term overcurrent (OC). However, PCM in the path of heat conduction could impede cooling in normal operation. This article proposes a dual-mode thermal management approach for a three-dimensional loop packaging design of a half-bridge SiC mosfet power module, in which the PCM is placed away from the primary heat conduction path and is only activated by the OC. This offers thermal buffering during OC without notably increasing the steady-state thermal resistance. Chip temperatures of the upper and lower legs, on the two sides of the PCM, are almost equal and consistent with values in a package without PCM. The 1200 V, 80 A prototype is shown to have superior performance to a conventional module with single-sided cooling. Testing under 3 p.u. and 10 s OC shows that integrating PCM can reduce the chip temperature rise by about 11°C. The PCM thermal buffering effect in repetitive transients is demonstrated and evaluated. Double pulse testing shows improved switching characteristics. The parasitic loop inductance is measured to be 5.67 and 7 nH in static and dynamic conditions, respectively, and the simulated value is 5.25 nH. Thermal cycling results confirm the proposed module's reliability comparable to the conventional double-sided design.
- 26 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40 (11) , 16979-16994
Stress Management of Wind Turbine Components Using a Nano-Enhanced Phase Change Material Integrated Power Module
Offshore wind turbine components endure high mechanical and thermal stress due to fluctuating wind conditions and harsh marine environments, but lack coordinated stress management due to the low thermal inertia of the power electronic system. Frequent and large pitch movements further aggravate component stress. This article introduces a power module packaging method that integrates nano-enhanced phase change materials (PCMs) to provide short-term overload capability. By mixing PCMs with carbon nanotubes, the thermal resistance per insulated gate bipolar transistor (IGBT) of the nano-enhanced PCM module is reduced by 34% and 14% compared to the conventional module and PCM module respectively due to the increased thermal conductivity of PCMs. Finite element analysis and experimental results demonstrate the superior thermal performance of the nano-enhanced PCM module over traditional modules. Based on this improved functionality, a stress management strategy is proposed to mitigate mechanical stress on the pitch system by increasing the rated wind speed and temporarily overloading the turbine powertrain system. Statistical analysis based on real wind speed profiles validates the strategy’s effectiveness, showing a reduction in the number of pitch angle cycles by up to 86% .
- 26 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40 (11) , 16979-16994
Stress Management of Wind Turbine Components Using a Nano-Enhanced Phase Change Material Integrated Power Module
Offshore wind turbine components endure high mechanical and thermal stress due to fluctuating wind conditions and harsh marine environments, but lack coordinated stress management due to the low thermal inertia of the power electronic system. Frequent and large pitch movements further aggravate component stress. This article introduces a power module packaging method that integrates nano-enhanced phase change materials (PCMs) to provide short-term overload capability. By mixing PCMs with carbon nanotubes, the thermal resistance per insulated gate bipolar transistor (IGBT) of the nano-enhanced PCM module is reduced by 34% and 14% compared to the conventional module and PCM module respectively due to the increased thermal conductivity of PCMs. Finite element analysis and experimental results demonstrate the superior thermal performance of the nano-enhanced PCM module over traditional modules. Based on this improved functionality, a stress management strategy is proposed to mitigate mechanical stress on the pitch system by increasing the rated wind speed and temporarily overloading the turbine powertrain system. Statistical analysis based on real wind speed profiles validates the strategy’s effectiveness, showing a reduction in the number of pitch angle cycles by up to 86% .
- 9 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40 (10) , 15381-15398
Single-Phase and Evaporating Two-Phase Flow Microchannel Cooling of Power Modules for Temporary Overcurrent Operation
Evaporating two-phase flows are usually avoided in cooling applications due to the potential inception of flow instabilities, which result in worse cooling performance. However, the substantial latent heat of liquid evaporation presents a compelling source in power electronics cooling when temporary overcurrent is needed. In this study, we utilise water evaporation to enhance the cooling performance under temporary module overcurrent conditions, while the water remains in its liquid phase during nominal operation. The proof-of-concept is demonstrated for a Si IGBT/diode half-bridge module cooled with a microchannel array integrated below the direct bonded copper ceramic. The microchannel cooling solution is evaluated in terms of reduction in the junction-to-case thermal resistance and of an increase in the temporary overcurrent capability. The thermal resistance is extracted for different flow rates using Simcenter Micred Power Tester. Infrared and visible spectrum cameras are used to simultaneously record the junction temperature and the evaporating flow in the microchannel array. Flow regimes with parts of individual channels occupied by the flow of vapor have been observed in the overcurrent duration, resulting in heat transported downstream from the chip location, where liquid evaporates, to the outlet of the manifold. Results indicate that evaporation enhances the cooling performance for the tested conditions, with no signs of boiling crisis in the microchannel flow.
- 9 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40 (10) , 15381-15398
Single-Phase and Evaporating Two-Phase Flow Microchannel Cooling of Power Modules for Temporary Overcurrent Operation
Evaporating two-phase flows are usually avoided in cooling applications due to the potential inception of flow instabilities, which result in worse cooling performance. However, the substantial latent heat of liquid evaporation presents a compelling source in power electronics cooling when temporary overcurrent is needed. In this study, we utilise water evaporation to enhance the cooling performance under temporary module overcurrent conditions, while the water remains in its liquid phase during nominal operation. The proof-of-concept is demonstrated for a Si IGBT/diode half-bridge module cooled with a microchannel array integrated below the direct bonded copper ceramic. The microchannel cooling solution is evaluated in terms of reduction in the junction-to-case thermal resistance and of an increase in the temporary overcurrent capability. The thermal resistance is extracted for different flow rates using Simcenter Micred Power Tester. Infrared and visible spectrum cameras are used to simultaneously record the junction temperature and the evaporating flow in the microchannel array. Flow regimes with parts of individual channels occupied by the flow of vapor have been observed in the overcurrent duration, resulting in heat transported downstream from the chip location, where liquid evaporates, to the outlet of the manifold. Results indicate that evaporation enhances the cooling performance for the tested conditions, with no signs of boiling crisis in the microchannel flow.
- 23 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 13 (4) , 4488-4503
A Comparative Study of Thermal Management Strategies for Overcurrent in Aircraft Power Electronics Applications
The increasing power density in More Electric Aircraft (MEA) systems poses significant thermal challenges for power electronics, especially during overcurrent scenarios and fault conditions throughout flight cycles. Efficient thermal management is therefore essential. This paper presents a comparative study of three thermal management strategies— liquid metal phase change material (PCM), thermoelectric cooling (TEC), and heat pipes—evaluated in terms of time-scale response and thermal performance under overcurrent conditions. Results indicate that liquid metal PCM responds in the seconds range, while TEC and heat pipes provide faster responses in the milliseconds range. All three strategies demonstrated significant improvements over conventional power module designs, achieving thermal resistance reductions of 45%, 35%, and 21% for heat pipe, TEC, and PCM, respectively. The heat pipe configuration exhibited the lowest thermal resistance and the most substantial reduction in junction temperature during overcurrent conditions. The overcurrent cycling test demonstrates that all three strategies effectively reduce both the mean junction temperature and junction temperature swing, resulting in an increased number of cycles to failure.
- 23 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 13 (4) , 4488-4503
A Comparative Study of Thermal Management Strategies for Overcurrent in Aircraft Power Electronics Applications
The increasing power density in More Electric Aircraft (MEA) systems poses significant thermal challenges for power electronics, especially during overcurrent scenarios and fault conditions throughout flight cycles. Efficient thermal management is therefore essential. This paper presents a comparative study of three thermal management strategies— liquid metal phase change material (PCM), thermoelectric cooling (TEC), and heat pipes—evaluated in terms of time-scale response and thermal performance under overcurrent conditions. Results indicate that liquid metal PCM responds in the seconds range, while TEC and heat pipes provide faster responses in the milliseconds range. All three strategies demonstrated significant improvements over conventional power module designs, achieving thermal resistance reductions of 45%, 35%, and 21% for heat pipe, TEC, and PCM, respectively. The heat pipe configuration exhibited the lowest thermal resistance and the most substantial reduction in junction temperature during overcurrent conditions. The overcurrent cycling test demonstrates that all three strategies effectively reduce both the mean junction temperature and junction temperature swing, resulting in an increased number of cycles to failure.
- Top Cited Papers
- 10 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 13 (2) , 2158-2172
Substrate-Less Power Semiconductor Packaging for the Potential of Recyclability
Recyclability is being pursued in power electronics. Power semiconductor devices and modules are some of the core components, featuring high material and energy costs in fabrication, but with limited-service lifetime. This study explores a packaging structure which might improve their recyclability in the future. The study focuses on the cooling and electric insulation aspects of the substrate-less design. A customized 3-sectional heat pipe is used to replace the ceramic based direct bonded copper (DBC) or active metal brazed (AMB), which are difficult to recycle. It is assumed that the commonly used thermoset plastic casing and silicone gel can be replaced by recyclable polyetherimide (PEI) encapsulation. A design procedure is proposed to match the specifications of the heat pipe with the thermal dissipation and electric insulation requirements of the power device. The thermal resistance of junction-heatsink is shown to be much lower than that of a typical substrate. The electric insulation strength is compared for different working fluids to identify a satisfactory solution.
- 10 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 13 (2) , 2158-2172
Top Cited PapersSubstrate-Less Power Semiconductor Packaging for the Potential of Recyclability
Recyclability is being pursued in power electronics. Power semiconductor devices and modules are some of the core components, featuring high material and energy costs in fabrication, but with limited-service lifetime. This study explores a packaging structure which might improve their recyclability in the future. The study focuses on the cooling and electric insulation aspects of the substrate-less design. A customized 3-sectional heat pipe is used to replace the ceramic based direct bonded copper (DBC) or active metal brazed (AMB), which are difficult to recycle. It is assumed that the commonly used thermoset plastic casing and silicone gel can be replaced by recyclable polyetherimide (PEI) encapsulation. A design procedure is proposed to match the specifications of the heat pipe with the thermal dissipation and electric insulation requirements of the power device. The thermal resistance of junction-heatsink is shown to be much lower than that of a typical substrate. The electric insulation strength is compared for different working fluids to identify a satisfactory solution.
- 7 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Dielectrics and Electrical Insulation
- Vol. 32 (2) , 815-822
Evidently Retarded Degradation in Breakdown Strength of Polypropylene Eco-Friendly Cable Insulation From Trace Self-Grown γ-Crystals During Thermal Aging
Recyclable thermoplastic polypropylene (PP) cable insulation with excellent performances is expected to represent traditional thermoset cross-linked polyethylene (XLPE) insulation. However, the poor resistance to thermal ageing of PP-based cable insulation is generally considered as an obstacle limiting their practical applications. In this paper, trace self-grown γ-crystals of PP were accidentally found in impact polypropylene copolymer (IPC) cable insulation during thermal ageing, which evidently retarded degradation in breakdown strength caused by decline in crystallinity. The unexpected growth of γ-crystals is further proven to be facilitated by crystalline ethylene segments from rubber phases and those blocked in PP chains. As a result, more deep traps are introduced by γ-crystals that are presented as crystalline structure defects. It makes carriers in IPC more difficult to migrate and detrap under external electric field. Therefore, although the crystallinity, which determines the breakdown strength of semi-crystalline polymers, decreases at day 12 of thermal ageing, the degradation in breakdown strength is delayed until day 24. The self-grown γ-crystals in IPC insulation thus achieve the self-protective resistance against thermal ageing. This work provides a new understanding to the effect of elastomers on thermal-ageing stability in PP-based eco-friendly power cable insulation.
- 7 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Dielectrics and Electrical Insulation
- Vol. 32 (2) , 815-822
Evidently Retarded Degradation in Breakdown Strength of Polypropylene Eco-Friendly Cable Insulation From Trace Self-Grown γ-Crystals During Thermal Aging
Recyclable thermoplastic polypropylene (PP) cable insulation with excellent performances is expected to represent traditional thermoset cross-linked polyethylene (XLPE) insulation. However, the poor resistance to thermal ageing of PP-based cable insulation is generally considered as an obstacle limiting their practical applications. In this paper, trace self-grown γ-crystals of PP were accidentally found in impact polypropylene copolymer (IPC) cable insulation during thermal ageing, which evidently retarded degradation in breakdown strength caused by decline in crystallinity. The unexpected growth of γ-crystals is further proven to be facilitated by crystalline ethylene segments from rubber phases and those blocked in PP chains. As a result, more deep traps are introduced by γ-crystals that are presented as crystalline structure defects. It makes carriers in IPC more difficult to migrate and detrap under external electric field. Therefore, although the crystallinity, which determines the breakdown strength of semi-crystalline polymers, decreases at day 12 of thermal ageing, the degradation in breakdown strength is delayed until day 24. The self-grown γ-crystals in IPC insulation thus achieve the self-protective resistance against thermal ageing. This work provides a new understanding to the effect of elastomers on thermal-ageing stability in PP-based eco-friendly power cable insulation.
- Open Access
- 22 May 2024
- Published by Institution of Engineering and Technology (IET) in High Voltage
- Vol. 9 (4) , 763-772
Degradation of superhydrophobic aluminium overhead line conductor surfaces
It has been shown that noise emissions from HV overhead line conductors can be reduced under rain conditions by making their surfaces superhydrophobic. The working environment makes ensuring the longevity of any treatment a major challenge. The degradation of various superhydrophobic surfaces generated by applying a superhydrophobic coating and patterning microscale channels is assessed under an AC electric field (18 kV/cm) with continuous water spray. By examining the droplet distribution on the surfaces during the degradation and the surface roughness before and after degradation, the authors demonstrate that no water droplets were found on the microscale patterned surface, but droplets were formed on the coated surface after degradation. The surface roughness reduction of the coated surface and microscale patterned surface was 29.8% and 11.3%, respectively, indicating that the microscale patterned surface has better durability than the superhydrophobic coating under the AC electric stress.
- 22 May 2024
- Published by Institution of Engineering and Technology (IET) in High Voltage
- Vol. 9 (4) , 763-772
Open AccessDegradation of superhydrophobic aluminium overhead line conductor surfaces
It has been shown that noise emissions from HV overhead line conductors can be reduced under rain conditions by making their surfaces superhydrophobic. The working environment makes ensuring the longevity of any treatment a major challenge. The degradation of various superhydrophobic surfaces generated by applying a superhydrophobic coating and patterning microscale channels is assessed under an AC electric field (18 kV/cm) with continuous water spray. By examining the droplet distribution on the surfaces during the degradation and the surface roughness before and after degradation, the authors demonstrate that no water droplets were found on the microscale patterned surface, but droplets were formed on the coated surface after degradation. The surface roughness reduction of the coated surface and microscale patterned surface was 29.8% and 11.3%, respectively, indicating that the microscale patterned surface has better durability than the superhydrophobic coating under the AC electric stress.
- Open Access
Over-Current Capability of Silicon Carbide and Silicon Devices for Short Power Pulses with Copper and Phase Change Materials below the Chip
An increasing share of fluctuating and intermittent renewable energy sources can cause over-currents (OCs) in the power system. The heat generated during OCs increases the junction temperature of semiconductor devices and could even lead to thermal runaway if thermal limits are reached. In order to keep the junction temperature within the thermal limit of the semiconductor, the power module structure with heat-absorbing material below the chip is investigated through COMSOL Multiphysics simulations. The upper limits of the junction temperature for Silicon (Si) and Silicon Carbide (SiC) are assumed to be 175 and 250 C, respectively. The heat-absorbing materials considered for analysis are a copper block and a copper block with phase change materials (PCMs). Two times, three times, and four times of OCs would be discussed for durations of a few hundred milliseconds and seconds. This article also discusses the thermal performance of a copper block and a copper block with PCMs. PCMs used for Si and SiC are LM108 and Lithium, respectively. It is concluded that the copper block just below the semiconductor chip would enable OC capability in Si and SiC devices and would be more convenient to manufacture as compared to the copper block with PCM.Open AccessOver-Current Capability of Silicon Carbide and Silicon Devices for Short Power Pulses with Copper and Phase Change Materials below the Chip
An increasing share of fluctuating and intermittent renewable energy sources can cause over-currents (OCs) in the power system. The heat generated during OCs increases the junction temperature of semiconductor devices and could even lead to thermal runaway if thermal limits are reached. In order to keep the junction temperature within the thermal limit of the semiconductor, the power module structure with heat-absorbing material below the chip is investigated through COMSOL Multiphysics simulations. The upper limits of the junction temperature for Silicon (Si) and Silicon Carbide (SiC) are assumed to be 175 and 250 C, respectively. The heat-absorbing materials considered for analysis are a copper block and a copper block with phase change materials (PCMs). Two times, three times, and four times of OCs would be discussed for durations of a few hundred milliseconds and seconds. This article also discusses the thermal performance of a copper block and a copper block with PCMs. PCMs used for Si and SiC are LM108 and Lithium, respectively. It is concluded that the copper block just below the semiconductor chip would enable OC capability in Si and SiC devices and would be more convenient to manufacture as compared to the copper block with PCM. - 12 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Delivery
- Vol. 38 (6) , 3771-3781
Audible Noise and Corona Discharge From Water Droplets on Superhydrophobic HVAC Conductors
Audible noise from transmission lines is mainly generated by corona discharge from defects and water droplets on the conductors’ surface. Applying a superhydrophobic coating to the conductors can reduce corona discharge, thereby reducing the level of audible noise produced. In this article, corona discharge and noise measurements from an untreated conductor and a conductor coated with superhydrophobic coatings were carried out in AC electric fields and continuous water spray. The coated conductors show higher partial discharge inception voltages (PDIV) than uncoated ones. PD magnitude and PD per cycle of the coated conductors are lower compared with uncoated conductors, especially at electric fields above 14 kV/cm. A linear correlation between overall sound pressure and total PD magnitude is established. The behavior of corona discharges from single droplets with various sizes and positions and associated droplet vibration were investigated and the local electric field enhancement was analyzed by finite element analysis to examine the influence of droplet size and position on electric field distribution. Superhydrophobic coatings result in reduced PD magnitude and number and therefore reduce audible noise generated. This is attributed to small sessile droplets forming rather than large pendant droplets.
- 12 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Delivery
- Vol. 38 (6) , 3771-3781
Audible Noise and Corona Discharge From Water Droplets on Superhydrophobic HVAC Conductors
Audible noise from transmission lines is mainly generated by corona discharge from defects and water droplets on the conductors’ surface. Applying a superhydrophobic coating to the conductors can reduce corona discharge, thereby reducing the level of audible noise produced. In this article, corona discharge and noise measurements from an untreated conductor and a conductor coated with superhydrophobic coatings were carried out in AC electric fields and continuous water spray. The coated conductors show higher partial discharge inception voltages (PDIV) than uncoated ones. PD magnitude and PD per cycle of the coated conductors are lower compared with uncoated conductors, especially at electric fields above 14 kV/cm. A linear correlation between overall sound pressure and total PD magnitude is established. The behavior of corona discharges from single droplets with various sizes and positions and associated droplet vibration were investigated and the local electric field enhancement was analyzed by finite element analysis to examine the influence of droplet size and position on electric field distribution. Superhydrophobic coatings result in reduced PD magnitude and number and therefore reduce audible noise generated. This is attributed to small sessile droplets forming rather than large pendant droplets.
- Open Access
- 1 January 2023
- Published by IMAPS - International Microelectronics Assembly and Packaging Society in International Symposium on Microelectronics
- Vol. 2023 (EMPC) , 381-385
Thickness Effect of Copper Clips on Power Module Packaging Design
The superior switching performance of SiC MOSFETs compared to Si devices is limited by packaging-related issues. High electromagnetic parasitics which lead to high voltage overshoots, and higher power losses are the main challenges of high frequency operation. Hence, packaging design modification and optimisation are necessary to accommodate faster switching. Copper clips replacing the bonding wires show promising results in reducing stray inductances, while enhancing the current conduction and heat dissipation since the clip are in contact with a larger area of the semiconductor chip. Silver sintering instead of soldering further improves the electrothermal behaviour. This paper investigates numerically various thicknesses of the copper clips and their effect on double-sided silver sintering, half-bridge 1200V/400A SiC MOSFET power module. Moreover, the silver layer thickness is varied to reduce th maximum stresses on the chip - silver interface.
- 1 January 2023
- Published by IMAPS - International Microelectronics Assembly and Packaging Society in International Symposium on Microelectronics
- Vol. 2023 (EMPC) , 381-385
Open AccessThickness Effect of Copper Clips on Power Module Packaging Design
The superior switching performance of SiC MOSFETs compared to Si devices is limited by packaging-related issues. High electromagnetic parasitics which lead to high voltage overshoots, and higher power losses are the main challenges of high frequency operation. Hence, packaging design modification and optimisation are necessary to accommodate faster switching. Copper clips replacing the bonding wires show promising results in reducing stray inductances, while enhancing the current conduction and heat dissipation since the clip are in contact with a larger area of the semiconductor chip. Silver sintering instead of soldering further improves the electrothermal behaviour. This paper investigates numerically various thicknesses of the copper clips and their effect on double-sided silver sintering, half-bridge 1200V/400A SiC MOSFET power module. Moreover, the silver layer thickness is varied to reduce th maximum stresses on the chip - silver interface.