Clement Nguyen Thanh Dao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Clement Nguyen Thanh Dao has a total of 100 co-authors. Here are the top co-authors by number of shared publications:
- Alexandre Torre
CEA, IRFM, Centre de Cadarache, Saint-Paul-lez-Durance, France
9 shared publications - Thierry Schild
ITER Organization, St. Paul Lez durance Cedex, France
6 shared publications - Valentina Corato
ENEA, Frascati, Italy
5 shared publications - Benoit Lacroix
CEA-IRFM, St-Paul Lez Durance, France
4 shared publications - Nicolai Martovetsky
US ITER Project, Oak Ridge National Laboratory, Oak Ridge, TN, USA
4 shared publications - Quentin Le Coz
CEA-IRFM, St-Paul Lez Durance, France
4 shared publications
Latest Publications
- 25 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (3) , 1-6
Magnet Design Activities at CEA for EU-DEMO LAR Baseline 2024
In 2024, a new EU-DEMO baseline (called LAR for Low Aspect Ratio) was released which substantially changed the constraints on the magnets systems, with a key driver for changes the magnet systems being mechanical considerations. This paper will briefly list changes in the new baseline, and give an overview of updates to the CEA design toolbox MADMACS, particularly the implementation of fatigue analysis for the pulsed central solenoid (CS), and consideration of hybrid low/high-temperature superconducting CS coils. The new fatigue tool is later used to perform sensitivity analysis on the assumed parameters for Walker exponent and residual stress, with results showing that further study of these parameters should be of high priority. Summaries of new preliminary toroidal field (TF) coil and CS designs, based on ITER-like approaches, are also given. The final TF design required modifications to the winding pack dimensions, and the CS could only meet all the requirements using HTS inner turns, new jacket materials, and relaxations in fatigue assumptions. Therefore, it is clear that the LAR baseline has not yet resolved the static and fatigue concerns for the magnet systems, when considering ITER-like TF and CS solutions, but that this may be possible with further development.
- 25 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (3) , 1-6
Magnet Design Activities at CEA for EU-DEMO LAR Baseline 2024
In 2024, a new EU-DEMO baseline (called LAR for Low Aspect Ratio) was released which substantially changed the constraints on the magnets systems, with a key driver for changes the magnet systems being mechanical considerations. This paper will briefly list changes in the new baseline, and give an overview of updates to the CEA design toolbox MADMACS, particularly the implementation of fatigue analysis for the pulsed central solenoid (CS), and consideration of hybrid low/high-temperature superconducting CS coils. The new fatigue tool is later used to perform sensitivity analysis on the assumed parameters for Walker exponent and residual stress, with results showing that further study of these parameters should be of high priority. Summaries of new preliminary toroidal field (TF) coil and CS designs, based on ITER-like approaches, are also given. The final TF design required modifications to the winding pack dimensions, and the CS could only meet all the requirements using HTS inner turns, new jacket materials, and relaxations in fatigue assumptions. Therefore, it is clear that the LAR baseline has not yet resolved the static and fatigue concerns for the magnet systems, when considering ITER-like TF and CS solutions, but that this may be possible with further development.
- 22 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (3) , 1-6
Study of CORC Conductors With Respect to Individual Tape Properties
CEA has been studying the advantages of a conductor based on an assembly of CORC cables in the high field zone of a hybrid Central Solenoid (CS) magnet for EU-DEMO. To this end, the detailed study of geometrical and electrical parameters of a CORC structure are studied in order to evaluate the cable’s electrical performance as well as to determine a number of important parameters (crossing points, contact surface etc…) as function of the cable structure. The paper first presents these geometrical and performance analyses. It will then try to introduce smeared models in order to reduce the cable’s performance to 1D tape scaling law using effective parameters. That reduction is of importance for use in thermohydraulic models. Finally, the paper will present the case study of a particular CORC conductor that is being procured and is foreseen to be tested in SULTAN in 2025. The paper will try to give some predictive estimate of the cable performance and identify some of the unknowns related to current redistribution and joint resistance.
- 22 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (3) , 1-6
Study of CORC Conductors With Respect to Individual Tape Properties
CEA has been studying the advantages of a conductor based on an assembly of CORC cables in the high field zone of a hybrid Central Solenoid (CS) magnet for EU-DEMO. To this end, the detailed study of geometrical and electrical parameters of a CORC structure are studied in order to evaluate the cable’s electrical performance as well as to determine a number of important parameters (crossing points, contact surface etc…) as function of the cable structure. The paper first presents these geometrical and performance analyses. It will then try to introduce smeared models in order to reduce the cable’s performance to 1D tape scaling law using effective parameters. That reduction is of importance for use in thermohydraulic models. Finally, the paper will present the case study of a particular CORC conductor that is being procured and is foreseen to be tested in SULTAN in 2025. The paper will try to give some predictive estimate of the cable performance and identify some of the unknowns related to current redistribution and joint resistance.
- 11 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-6
The CIRCE Code: Cast3M Investigation and Research for Coils Mechanical Evaluation
The recent success of demonstration coils using HTS confirms the promising application of these materials for toroidal field (TF) coils in high-field fusion machines. Potential magnetic fields at around 20 T on the conductor claim to achieve the required performance for commercial reactors with fusion power scaling as ${{P}_f} \propto B_t^4$ under several assumptions. However, this usually involves increased engineering challenges to withstand much higher mechanical loads scaling quadratically with the magnetic field. This paper presents a new mechanical toolbox, named CIRCE: a highly configurable code featuring plane stress analysis and 3D beam analysis, with a case study of tokamak TF coils under in-plane and out-of-plane loads.
- 11 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-6
The CIRCE Code: Cast3M Investigation and Research for Coils Mechanical Evaluation
The recent success of demonstration coils using HTS confirms the promising application of these materials for toroidal field (TF) coils in high-field fusion machines. Potential magnetic fields at around 20 T on the conductor claim to achieve the required performance for commercial reactors with fusion power scaling as ${{P}_f} \propto B_t^4$ under several assumptions. However, this usually involves increased engineering challenges to withstand much higher mechanical loads scaling quadratically with the magnetic field. This paper presents a new mechanical toolbox, named CIRCE: a highly configurable code featuring plane stress analysis and 3D beam analysis, with a case study of tokamak TF coils under in-plane and out-of-plane loads.
- 20 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-5
Design and Qualification of LTS Conductors at CEA for EU-DEMO Toroidal Field Magnet
The EU-DEMO baseline follows the path towards a large-scale tokamak demonstrator. The unmatched size stands as one of the biggest challenge to overcome. Toroidal field magnets are no exception and the expanding performance and limits require the development of new conductor designs. In this regard, CEA design team has been working on the scaling-up of ITER-like conductor technology, with the design, manufacture and test of a square-in-square 100 kA-class conductor called DEMOTF-WP3. It has now been tested in SULTAN and this article presents preliminary results. The sample is composed by two legs containing the same 3.5 m long CICC for redundancy purpose. Voltage taps and temperature sensors are installed along both legs following a symmetrical scheme. This sample also contains a twinbox joint prototype connecting the two legs together at the bottom of the sample thanks to a thin layer of compacted indium. Furthermore, the need expressed at EU-DEMO Gate 1 review to investigate round-in-round geometry permitting the use of radial plates, triggered the CEA design team to propose another Nb3Sn conductor design (DEMOTF-WP4), with operating current of 116 kA and peak field of 12.5 T. This conductor is composed of 721 SC strands and 1108 copper strands cabled together within a round stainless steel jacket with a diameter of 55 mm. The detailed design is presented along with the prototype manufactured that will be used for the qualification tests to be held at SULTAN facility at CRPP in 2025.
- 20 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-5
Design and Qualification of LTS Conductors at CEA for EU-DEMO Toroidal Field Magnet
The EU-DEMO baseline follows the path towards a large-scale tokamak demonstrator. The unmatched size stands as one of the biggest challenge to overcome. Toroidal field magnets are no exception and the expanding performance and limits require the development of new conductor designs. In this regard, CEA design team has been working on the scaling-up of ITER-like conductor technology, with the design, manufacture and test of a square-in-square 100 kA-class conductor called DEMOTF-WP3. It has now been tested in SULTAN and this article presents preliminary results. The sample is composed by two legs containing the same 3.5 m long CICC for redundancy purpose. Voltage taps and temperature sensors are installed along both legs following a symmetrical scheme. This sample also contains a twinbox joint prototype connecting the two legs together at the bottom of the sample thanks to a thin layer of compacted indium. Furthermore, the need expressed at EU-DEMO Gate 1 review to investigate round-in-round geometry permitting the use of radial plates, triggered the CEA design team to propose another Nb3Sn conductor design (DEMOTF-WP4), with operating current of 116 kA and peak field of 12.5 T. This conductor is composed of 721 SC strands and 1108 copper strands cabled together within a round stainless steel jacket with a diameter of 55 mm. The detailed design is presented along with the prototype manufactured that will be used for the qualification tests to be held at SULTAN facility at CRPP in 2025.
- 14 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-5
ITER Magnets Superconducting Joints Prototype Tests in the CEA SELFIE Facility for Operators Qualification
The Central Solenoid (CS) is the core element of the ITER magnet system, contributed as in-kind procurement by the US Domestic Agency. Each CS module uses a Nb 3 Sn conductor internally cooled by circulation of supercritical helium at 4.5 K and individually supplied up to a 45 kA current by two superconducting leads each connected through a Compacted Coaxial Joint (CCJ) and a Main Busbar (MB) joint to the Feeders system. This paper presents the results of the CCJ and MB prototypes cryogenic qualification in the dedicated SELFIE facility (ITER SELf-FIEld joint test facility). We will first introduce the specific SELFIE samples design, assembly and dedicated instrumentation used during the nominal current test and outline the main SELFIE interfaces. This will include in particular the indium-compacted electrical connection to the facility and the lower joint, which are necessary for a total facility secondary loop resistance. Then, we will detail the training environment and procedures, stressing out the knowledge transfer and risk mitigation strategy to avoid underperforming joints, which are only detectable after full assembly and cool-down of the tokamak. Finally, we will outline the first results and statistical analysis of the CCJ and MB joints testing, explaining the data-reduction scheme, comparing with SULTAN results and showing the effectiveness of the CCJ re-designing for a low-resistance simpler and more robust joint concept. Using these results, along with previous SULTAN results, we will try to estimate the in-coil performance of the joints.
- 14 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-5
ITER Magnets Superconducting Joints Prototype Tests in the CEA SELFIE Facility for Operators Qualification
The Central Solenoid (CS) is the core element of the ITER magnet system, contributed as in-kind procurement by the US Domestic Agency. Each CS module uses a Nb 3 Sn conductor internally cooled by circulation of supercritical helium at 4.5 K and individually supplied up to a 45 kA current by two superconducting leads each connected through a Compacted Coaxial Joint (CCJ) and a Main Busbar (MB) joint to the Feeders system. This paper presents the results of the CCJ and MB prototypes cryogenic qualification in the dedicated SELFIE facility (ITER SELf-FIEld joint test facility). We will first introduce the specific SELFIE samples design, assembly and dedicated instrumentation used during the nominal current test and outline the main SELFIE interfaces. This will include in particular the indium-compacted electrical connection to the facility and the lower joint, which are necessary for a total facility secondary loop resistance. Then, we will detail the training environment and procedures, stressing out the knowledge transfer and risk mitigation strategy to avoid underperforming joints, which are only detectable after full assembly and cool-down of the tokamak. Finally, we will outline the first results and statistical analysis of the CCJ and MB joints testing, explaining the data-reduction scheme, comparing with SULTAN results and showing the effectiveness of the CCJ re-designing for a low-resistance simpler and more robust joint concept. Using these results, along with previous SULTAN results, we will try to estimate the in-coil performance of the joints.
- 12 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-5
Studies of the CEA Design Proposals for EU-DEMO Magnets
The paper gives an overview of the latest magnet design activities at CEA for the EU-DEMO Magnet Systems. It explains the latest changes in design constraints, inputs and definitions, the updates that have been implemented in the design tools, and shows the latest CEA proposed design for the TF magnet. We will discuss the recent updates in the TF and PF design tools which were used in 2022 and 2023. In particular, the tools have evolved to include additional constraints or operating points like possible sub-cooling of the coils or synchronous discharge of the axisymmetric PF/CS system. The electromagnetic coupling of the TF coils with coil case and radial plates is also discussed during a fast safety discharge, along with energy extraction and deposition sharing. Furthermore, a new 2D TF mechanical model is presented that permits to make a fast iteration with design tools and optimize the radial build. Finally, the paper also includes an update on the CEA TF conductor qualification sample, describing in particular the latest results obtained in the Twente Press.
- 12 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-5
Studies of the CEA Design Proposals for EU-DEMO Magnets
The paper gives an overview of the latest magnet design activities at CEA for the EU-DEMO Magnet Systems. It explains the latest changes in design constraints, inputs and definitions, the updates that have been implemented in the design tools, and shows the latest CEA proposed design for the TF magnet. We will discuss the recent updates in the TF and PF design tools which were used in 2022 and 2023. In particular, the tools have evolved to include additional constraints or operating points like possible sub-cooling of the coils or synchronous discharge of the axisymmetric PF/CS system. The electromagnetic coupling of the TF coils with coil case and radial plates is also discussed during a fast safety discharge, along with energy extraction and deposition sharing. Furthermore, a new 2D TF mechanical model is presented that permits to make a fast iteration with design tools and optimize the radial build. Finally, the paper also includes an update on the CEA TF conductor qualification sample, describing in particular the latest results obtained in the Twente Press.
- 29 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-6
Progress of ITER Central Solenoid Assembly
This paper describes critical assembly process qualifications, acceptance criteria, and worker training of ITER Central Solenoid Assembly. Coaxial joint assembly was qualified and trained to achieve resistance below 4.1 nOhm. The electrical insulation process was qualified to 30 kV and 15 kV under Paschen conditions. Shear pin drilling and installation within specified tolerance was achieved. Modules were lifted and positioned within 2 mm. The lessons learned, and subsequent work execution onsite within the IO facility assembly hall are also presented.
- 29 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-6
Progress of ITER Central Solenoid Assembly
This paper describes critical assembly process qualifications, acceptance criteria, and worker training of ITER Central Solenoid Assembly. Coaxial joint assembly was qualified and trained to achieve resistance below 4.1 nOhm. The electrical insulation process was qualified to 30 kV and 15 kV under Paschen conditions. Shear pin drilling and installation within specified tolerance was achieved. Modules were lifted and positioned within 2 mm. The lessons learned, and subsequent work execution onsite within the IO facility assembly hall are also presented.
- 15 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-5
Installation Progress of the Central Solenoid (CS) on ITER Site
The installation process of the Central Solenoid (CS) on the ITER site is a complex and multi-step process that involves careful planning, engineering, and construction. The CS occupies the bore of the ITER tokomak and provides a dynamic magnetic field which inductively drives the plasma current. The CS assembly consists of a stack of six modules each electrically connected to bus bars and mechanically bonded with an external structure as shown in (Fig. 1 ). Each module is connected to its bus bar with a pair of coaxial joints. This document will provide a brief overview of the recent installation progress, and then will focus on several critical steps of one module stacking, such as lifting and joint assembly.
- 15 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-5
Installation Progress of the Central Solenoid (CS) on ITER Site
The installation process of the Central Solenoid (CS) on the ITER site is a complex and multi-step process that involves careful planning, engineering, and construction. The CS occupies the bore of the ITER tokomak and provides a dynamic magnetic field which inductively drives the plasma current. The CS assembly consists of a stack of six modules each electrically connected to bus bars and mechanically bonded with an external structure as shown in (Fig. 1 ). Each module is connected to its bus bar with a pair of coaxial joints. This document will provide a brief overview of the recent installation progress, and then will focus on several critical steps of one module stacking, such as lifting and joint assembly.
- 18 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-5
Heat Transfer Coefficient Measurement in Single Channel Cable-in-Conduit Conductor
Cable-in-conduit conductors (CICC) compose superconducting magnets of tokamaks and are cooled with 4 K supercritical helium forced flow, to provide efficient heat removal and thermal stability of the superconducting state. Nowadays, thermal couplings between fluid and solids are ill-characterized for such cables. We consequently measured global heat transfer interphase coefficients at macro scale. An experimental set-up associated with an inverse method and a direct three temperatures thermal-hydraulic model have been developed to obtain representative data. Transient experiments of forced flow with heat pulses imposing thermal disequilibrium between fluid and solids have been performed. Results are correlated to actual geometric properties obtained from 3D tomography. 1D three temperatures model of the two phases (bundle/nitrogen) along with the jacket, thermally coupled by convection is solved using finite volume method with an implicit and upstream scheme. Results are compared to available literature data.
- 18 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-5
Heat Transfer Coefficient Measurement in Single Channel Cable-in-Conduit Conductor
Cable-in-conduit conductors (CICC) compose superconducting magnets of tokamaks and are cooled with 4 K supercritical helium forced flow, to provide efficient heat removal and thermal stability of the superconducting state. Nowadays, thermal couplings between fluid and solids are ill-characterized for such cables. We consequently measured global heat transfer interphase coefficients at macro scale. An experimental set-up associated with an inverse method and a direct three temperatures thermal-hydraulic model have been developed to obtain representative data. Transient experiments of forced flow with heat pulses imposing thermal disequilibrium between fluid and solids have been performed. Results are correlated to actual geometric properties obtained from 3D tomography. 1D three temperatures model of the two phases (bundle/nitrogen) along with the jacket, thermally coupled by convection is solved using finite volume method with an implicit and upstream scheme. Results are compared to available literature data.
- 28 April 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 32 (6) , 1-5
Updates on CEA Design and Experimental Activities on EU DEMO TF System
In the framework of EU design activities for dimensioning the future fusion DEMOnstration reactor (DEMO), in-depth analyses were conducted in EUROfusion context, aiming to define the design of the DEMO magnets system. For the last DEMO baseline, CEA has proposed for Toroidal Field (TF) coils a concept with radial plates (named WP#4) which is ITER-like, with a round conductor embedded in steel plates. In order to consolidate this design, CEA conducted fine analyses that assess thermal hydraulic and mechanical aspects to allow ensuring compliance with design criteria. The outcomes of theses analyses were used to improve the TF design in order to avoid relying on conservative approaches at pre-design stage, which often end up in material over dimensioning, that penalize cost and space occupation. In this regard, two improving approaches will be exposed, that deal with mechanical consideration and temperature operation, together with future perspectives. On the other hand, CEA designed and manufactured in collaboration with ASIPP a full-size conductor sample derived from a previous TF CEA concept (square-in-square conductor) which is expected to operate at 88 kA and 12T. The two conductor legs of this sample were designed by CEA and manufactured by ASIPP following an extensive quality assurance (QA) preparation process. The sample is presently in course of assembly in CEA Cadarache and is expected to be tested in SULTAN facility (Villigen, CH) to assess its behaviour in both DC and AC regimes. An overview of the status of activities and future perspectives is given in this paper.
- 28 April 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 32 (6) , 1-5
Updates on CEA Design and Experimental Activities on EU DEMO TF System
In the framework of EU design activities for dimensioning the future fusion DEMOnstration reactor (DEMO), in-depth analyses were conducted in EUROfusion context, aiming to define the design of the DEMO magnets system. For the last DEMO baseline, CEA has proposed for Toroidal Field (TF) coils a concept with radial plates (named WP#4) which is ITER-like, with a round conductor embedded in steel plates. In order to consolidate this design, CEA conducted fine analyses that assess thermal hydraulic and mechanical aspects to allow ensuring compliance with design criteria. The outcomes of theses analyses were used to improve the TF design in order to avoid relying on conservative approaches at pre-design stage, which often end up in material over dimensioning, that penalize cost and space occupation. In this regard, two improving approaches will be exposed, that deal with mechanical consideration and temperature operation, together with future perspectives. On the other hand, CEA designed and manufactured in collaboration with ASIPP a full-size conductor sample derived from a previous TF CEA concept (square-in-square conductor) which is expected to operate at 88 kA and 12T. The two conductor legs of this sample were designed by CEA and manufactured by ASIPP following an extensive quality assurance (QA) preparation process. The sample is presently in course of assembly in CEA Cadarache and is expected to be tested in SULTAN facility (Villigen, CH) to assess its behaviour in both DC and AC regimes. An overview of the status of activities and future perspectives is given in this paper.