Tong Che
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Tong Che has a total of 58 co-authors. Here are the top co-authors by number of shared publications:
- Clement Nguyen Thanh Dao
CEA, IRFM, Centre de Cadarache, Saint-Paul-lez-Durance, France
3 shared publications - Haiyu Zhu
CNPE Consortium of ITER TAC1, Cadarache, France
3 shared publications - Lianli Shao
OAKRIDGE, Orlans, France
3 shared publications Pengfei Zheng
Center for Fusion Science, Southwestern Institute of Physics, Chengdu, China
3 shared publications- Thierry Schild
ITER Organization, St. Paul Lez durance Cedex, France
3 shared publications - Yasuyuki Miyoshi
ITER Organization, St. Paul Lez durance Cedex, France
3 shared publications
Latest Publications
- 24 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (9) , 1-9
Charging and Discharging Characteristics of a No-Insulation HTS Field Coil Wound for a Superconducting AC Homopolar Motor
No-insulation (NI) coils have become one of the most promising technologies for high-temperature superconducting (HTS) windings. In this paper, we focus on the charging and discharging characteristics of an NI coil wound for a superconducting AC homopolar motor. An electromagnetic thermal model that integrates an equivalent circuit model and a multi-physics model based on the A-formulation is developed and demonstrated by experiments to investigate the charging and discharging behavior of the NI coil. By using the model, the transport current distribution and the average heat loss are first studied, and the normalized current density distribution and heat loss distribution inside the NI coil during a charging and discharging process is presented. The results demonstrate that the turn-to-turn contact introduces charging/discharging delays of the NI coil. During charging, the most severe heat generation occurs when the operating current reaches its peak value, and is concentrated on middle turns of the coil. While during discharging, the maximum heat loss appears at the initial stage, and concentrates in the inner side of the coil. By accurately presenting the transient current distribution and the associated heat generation inside the NI coil, the proposed model provides both a theoretical foundation and a practical guideline for improving the stability of NI HTS coils in electrical applications.
- 24 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (9) , 1-9
Charging and Discharging Characteristics of a No-Insulation HTS Field Coil Wound for a Superconducting AC Homopolar Motor
No-insulation (NI) coils have become one of the most promising technologies for high-temperature superconducting (HTS) windings. In this paper, we focus on the charging and discharging characteristics of an NI coil wound for a superconducting AC homopolar motor. An electromagnetic thermal model that integrates an equivalent circuit model and a multi-physics model based on the A-formulation is developed and demonstrated by experiments to investigate the charging and discharging behavior of the NI coil. By using the model, the transport current distribution and the average heat loss are first studied, and the normalized current density distribution and heat loss distribution inside the NI coil during a charging and discharging process is presented. The results demonstrate that the turn-to-turn contact introduces charging/discharging delays of the NI coil. During charging, the most severe heat generation occurs when the operating current reaches its peak value, and is concentrated on middle turns of the coil. While during discharging, the maximum heat loss appears at the initial stage, and concentrates in the inner side of the coil. By accurately presenting the transient current distribution and the associated heat generation inside the NI coil, the proposed model provides both a theoretical foundation and a practical guideline for improving the stability of NI HTS coils in electrical applications.
- Open Access
Effect of Ball Milling Parameters on Properties of Nano-Sized Tungsten Powder via Mechanochemical Processing
Nano-sized tungsten exhibits superior properties due to its high-density grain boundaries’ strengthening. The high-quality nano-sized powder is essential for sintering nano-sized tungsten bulks through powder metallurgy techniques. In this study, nano-sized tungsten powder was successfully synthesized by mechanochemical methods using mixed WO3 and Mg powders. The effects of processing parameters on the morphology and microstructure of synthesized powder were thoroughly investigated. The results reveal that the thermite reaction of WO3 and Mg is almost complete after 5 min of ball milling at a speed of 300 rpm. The average grain size of the tungsten powder decreases with the increasing milling duration and speed. Optimal average grain size and purity were achieved at a milling speed of 300 rpm and a milling duration ranging from 30 to 120 min. Moreover, centrifugation sieving further reduces the average grain size of tungsten powder to 19.5 nm. In addition, the entire mechanochemical process can be divided into two stages: the reaction stage and the grain size refinement stage.
Open AccessEffect of Ball Milling Parameters on Properties of Nano-Sized Tungsten Powder via Mechanochemical Processing
Nano-sized tungsten exhibits superior properties due to its high-density grain boundaries’ strengthening. The high-quality nano-sized powder is essential for sintering nano-sized tungsten bulks through powder metallurgy techniques. In this study, nano-sized tungsten powder was successfully synthesized by mechanochemical methods using mixed WO3 and Mg powders. The effects of processing parameters on the morphology and microstructure of synthesized powder were thoroughly investigated. The results reveal that the thermite reaction of WO3 and Mg is almost complete after 5 min of ball milling at a speed of 300 rpm. The average grain size of the tungsten powder decreases with the increasing milling duration and speed. Optimal average grain size and purity were achieved at a milling speed of 300 rpm and a milling duration ranging from 30 to 120 min. Moreover, centrifugation sieving further reduces the average grain size of tungsten powder to 19.5 nm. In addition, the entire mechanochemical process can be divided into two stages: the reaction stage and the grain size refinement stage.
- 29 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (8) , 1-4
Experiment Research of Superconducting Joint Resistance in Large-Scale HTS Magnet
This study presents an experimental investigation into the resistance of superconducting joints in high temperature superconducting (HTS) linear plasma magnets. The focus is on examining the factors that influence joint resistance and how they can affect the overall performance and reliability of the magnet system. Through a series of rigorous experiments, key parameters such as air gaps, welding angles, and overlap lengths are analyzed to explore their impacts on joint resistance. The obtained results provide valuable insights into the design and optimization of superconducting joints for large-scale magnet applications, paving the way for improved performance and reliability in future superconducting technologies.
- 29 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (8) , 1-4
Experiment Research of Superconducting Joint Resistance in Large-Scale HTS Magnet
This study presents an experimental investigation into the resistance of superconducting joints in high temperature superconducting (HTS) linear plasma magnets. The focus is on examining the factors that influence joint resistance and how they can affect the overall performance and reliability of the magnet system. Through a series of rigorous experiments, key parameters such as air gaps, welding angles, and overlap lengths are analyzed to explore their impacts on joint resistance. The obtained results provide valuable insights into the design and optimization of superconducting joints for large-scale magnet applications, paving the way for improved performance and reliability in future superconducting technologies.
- 14 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-5
ITER Magnets Superconducting Joints Prototype Tests in the CEA SELFIE Facility for Operators Qualification
The Central Solenoid (CS) is the core element of the ITER magnet system, contributed as in-kind procurement by the US Domestic Agency. Each CS module uses a Nb 3 Sn conductor internally cooled by circulation of supercritical helium at 4.5 K and individually supplied up to a 45 kA current by two superconducting leads each connected through a Compacted Coaxial Joint (CCJ) and a Main Busbar (MB) joint to the Feeders system. This paper presents the results of the CCJ and MB prototypes cryogenic qualification in the dedicated SELFIE facility (ITER SELf-FIEld joint test facility). We will first introduce the specific SELFIE samples design, assembly and dedicated instrumentation used during the nominal current test and outline the main SELFIE interfaces. This will include in particular the indium-compacted electrical connection to the facility and the lower joint, which are necessary for a total facility secondary loop resistance. Then, we will detail the training environment and procedures, stressing out the knowledge transfer and risk mitigation strategy to avoid underperforming joints, which are only detectable after full assembly and cool-down of the tokamak. Finally, we will outline the first results and statistical analysis of the CCJ and MB joints testing, explaining the data-reduction scheme, comparing with SULTAN results and showing the effectiveness of the CCJ re-designing for a low-resistance simpler and more robust joint concept. Using these results, along with previous SULTAN results, we will try to estimate the in-coil performance of the joints.
- 14 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-5
ITER Magnets Superconducting Joints Prototype Tests in the CEA SELFIE Facility for Operators Qualification
The Central Solenoid (CS) is the core element of the ITER magnet system, contributed as in-kind procurement by the US Domestic Agency. Each CS module uses a Nb 3 Sn conductor internally cooled by circulation of supercritical helium at 4.5 K and individually supplied up to a 45 kA current by two superconducting leads each connected through a Compacted Coaxial Joint (CCJ) and a Main Busbar (MB) joint to the Feeders system. This paper presents the results of the CCJ and MB prototypes cryogenic qualification in the dedicated SELFIE facility (ITER SELf-FIEld joint test facility). We will first introduce the specific SELFIE samples design, assembly and dedicated instrumentation used during the nominal current test and outline the main SELFIE interfaces. This will include in particular the indium-compacted electrical connection to the facility and the lower joint, which are necessary for a total facility secondary loop resistance. Then, we will detail the training environment and procedures, stressing out the knowledge transfer and risk mitigation strategy to avoid underperforming joints, which are only detectable after full assembly and cool-down of the tokamak. Finally, we will outline the first results and statistical analysis of the CCJ and MB joints testing, explaining the data-reduction scheme, comparing with SULTAN results and showing the effectiveness of the CCJ re-designing for a low-resistance simpler and more robust joint concept. Using these results, along with previous SULTAN results, we will try to estimate the in-coil performance of the joints.
- 29 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-6
Progress of ITER Central Solenoid Assembly
This paper describes critical assembly process qualifications, acceptance criteria, and worker training of ITER Central Solenoid Assembly. Coaxial joint assembly was qualified and trained to achieve resistance below 4.1 nOhm. The electrical insulation process was qualified to 30 kV and 15 kV under Paschen conditions. Shear pin drilling and installation within specified tolerance was achieved. Modules were lifted and positioned within 2 mm. The lessons learned, and subsequent work execution onsite within the IO facility assembly hall are also presented.
- 29 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-6
Progress of ITER Central Solenoid Assembly
This paper describes critical assembly process qualifications, acceptance criteria, and worker training of ITER Central Solenoid Assembly. Coaxial joint assembly was qualified and trained to achieve resistance below 4.1 nOhm. The electrical insulation process was qualified to 30 kV and 15 kV under Paschen conditions. Shear pin drilling and installation within specified tolerance was achieved. Modules were lifted and positioned within 2 mm. The lessons learned, and subsequent work execution onsite within the IO facility assembly hall are also presented.
- 15 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-5
Installation Progress of the Central Solenoid (CS) on ITER Site
The installation process of the Central Solenoid (CS) on the ITER site is a complex and multi-step process that involves careful planning, engineering, and construction. The CS occupies the bore of the ITER tokomak and provides a dynamic magnetic field which inductively drives the plasma current. The CS assembly consists of a stack of six modules each electrically connected to bus bars and mechanically bonded with an external structure as shown in (Fig. 1 ). Each module is connected to its bus bar with a pair of coaxial joints. This document will provide a brief overview of the recent installation progress, and then will focus on several critical steps of one module stacking, such as lifting and joint assembly.
- 15 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-5
Installation Progress of the Central Solenoid (CS) on ITER Site
The installation process of the Central Solenoid (CS) on the ITER site is a complex and multi-step process that involves careful planning, engineering, and construction. The CS occupies the bore of the ITER tokomak and provides a dynamic magnetic field which inductively drives the plasma current. The CS assembly consists of a stack of six modules each electrically connected to bus bars and mechanically bonded with an external structure as shown in (Fig. 1 ). Each module is connected to its bus bar with a pair of coaxial joints. This document will provide a brief overview of the recent installation progress, and then will focus on several critical steps of one module stacking, such as lifting and joint assembly.
- 26 February 2022
- Published by Springer Nature in Journal of Superconductivity and Novel Magnetism
- Vol. 35 (5) , 1089-1098
HTS Joint Resistance for High-Field Magnets: Experiment and Temperature-Dependent Modeling
- 26 February 2022
- Published by Springer Nature in Journal of Superconductivity and Novel Magnetism
- Vol. 35 (5) , 1089-1098
HTS Joint Resistance for High-Field Magnets: Experiment and Temperature-Dependent Modeling
- 25 August 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 31 (8) , 1-4
Preliminary Design of a Superconducting LVDC Power Cable for Tokamak Application
Tokamak device requires a very high current power supply from the local power distribution sources to the targeted magnets such as toroidal field (TF) coils and poloidal field (PF) coils. This paper presents a preliminary design of a 30-m/1-kV/10-kA low voltage direct current (LVDC) superconducting cable for the potential in Tokamak applications. The outer diameter of the DC cable is 122.41 mm, and the pressure drop of liquid nitrogen (LN 2 ) in the inner and outer channels is about 6.59 kPa. The flow velocity of inner and outer LN 2 channels are 0.5 m/s and 0.25 m/s, respectively. The temperature rise of the entire cable was designed to be less than 5 K, which enhances the electricity supply safety and reliability. These preliminary design lays some technical bases for achieving high current and low loss power transmission. The designing results show that the LVDC superconducting cable has significant potentials for Tokamak applications compared with conventional copper cables.
- 25 August 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 31 (8) , 1-4
Preliminary Design of a Superconducting LVDC Power Cable for Tokamak Application
Tokamak device requires a very high current power supply from the local power distribution sources to the targeted magnets such as toroidal field (TF) coils and poloidal field (PF) coils. This paper presents a preliminary design of a 30-m/1-kV/10-kA low voltage direct current (LVDC) superconducting cable for the potential in Tokamak applications. The outer diameter of the DC cable is 122.41 mm, and the pressure drop of liquid nitrogen (LN 2 ) in the inner and outer channels is about 6.59 kPa. The flow velocity of inner and outer LN 2 channels are 0.5 m/s and 0.25 m/s, respectively. The temperature rise of the entire cable was designed to be less than 5 K, which enhances the electricity supply safety and reliability. These preliminary design lays some technical bases for achieving high current and low loss power transmission. The designing results show that the LVDC superconducting cable has significant potentials for Tokamak applications compared with conventional copper cables.